6
Form No. DR-5120
68-10219 rev01
Multi Language (rev. 10/9/13) © 2013 Gamco Commercial Restroom Accessories, A Division of Bobrick Printed in U.S.A.
GAMCo LIMITED TEN – YEAR WARRANTY.
Gamco Warm Air Hand Dryer, Model covered in this manual, is warranted by Gamco to the original user
against defects in workmanship or materials under normal use for 10 years after date of purchase for all components except motor brushes (3 years),
motor (5 years) and sensor (5 years). Any part which is determined to be defective in material or workmanship and returned to an authorized service
location, as Gamco designates, shipping costs prepaid, will be, as the exclusive remedy, repaired or replaced at Gamco’s option. For limited warranty
claim procedures, see PROMPT DISPOSITION below. This limited warranty gives purchasers specific rights from jurisdiction to jurisdiction.
LIMITATIoN oF LIABILITY.
T
o the extent allowable under applicable law, Gamco’s liability for consequential and incidental damages is expressly
disclaimed. Gamco’s liability in all events is limited to and shall not exceed the purchase price paid.
WARRANTY DISCLAIMER.
Gamco has made a diligent effort to provide product information and illustrate the products in this literature accurately;
however, such information and illustrations are for the sole purpose of identification, and do not express or imply a warranty that the products are
MERCHANTABLE, or FIT FOR A PARTICULAR PURPOSE, or that the products will necessary conform to the illustrations or descriptions. Except as
provided below, no warranty or affirmation on fact, expressed or implied, other than as stated in the “LIMITED WARRANTY” above is made or authorized
by Gamco.
PRoDUCT SUITABILITY.
Many jurisdictions have codes and regulations governing sales, construction, installation, and/or use of products for certain
purposes, which may vary from those in neighboring areas. While Gamco attempts to assure that the products comply with such codes, it cannot
guarantee compliance, and cannot be responsible for how the product is installed or used. Before purchase and use of a product, review the product
application, and all applicable national and local codes and regulations, and be sure that the product, installation, and use will comply with them.
Certain aspects of disclaimers are not applicable to consumer products; e.g., (a) some jurisdictions do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or exclusion may not apply to you; (b) also, some jurisdictions do not allow a limitation on how long
an implied warranty lasts, consequentially the above limitation may not apply to you; and (c) by law, during the period of this Limited Warranty, and
implied warranties of implied merchantability or fitness for particular purpose applicable tmer products purchased by consumers, may not be excluded or
otherwise disclaimed. Manufactured by World Dryer Corporation, Berkeley, Illinois 60163, U.S.A.
PRoMPT DISPoSITIoN.
Gamco will make a good faith effort for prompt correction or other adjustment with respect to any product which proves to be
defective within limited warranty. For any product believed to be defective within limited warranty, first write or call dealer from whom the product was
purchased. Dealer will give additional directions. If unable to resolve satisfactorily, write to Gamco at address below, giving dealer’s name, address, date,
and number of dealer’s invoice, and describing the nature of defect. Title and risk of loss pass to buyer on delivery to common carrier. If product was
damaged in transit to you, file claim with carrier
Limited Warranty
After power to dryer is switched
"ON", dryer runs for approximately
30 seconds, then will not restart.
Sensor obstruction or sensor lens
scratched or damaged.
Check sensor lens for foreign material or dirt. Clean lens with
soft damp cloth and mild cleaning agent. If sensor lens is
damaged or scratched, replace sensor.
Dryer "Ghosts" (starts with no
hands present.)
Mounted too close to counter or
object.
Relocate the object or dryer according to installation
instructions to a minimum 18" above any reflective surface and
at least 24" from an adjacent hand dryer.
Electrical noise from incoming
power supply or nearby infrared
actuated device.
Confirm dryer base is securely grounded.
Confirm dryer is on a dedicated circuit.
Check if any nearby infrared actuated device is triggering dryer.
Faulty circuit board (PCB)
Replace circuit board (PCB)
Dryer air too cold.
Heater control switch is in the
"OFF" position.
Re-position heater control switch to "ON".
Faulty circuit board (PCB)
Place hands under sensor. Listen for PCB relay "Click.". If no
"Click" is heard, replace the PCB.
Faulty heating element
If PCB Relay "Click" is heard and dryer continues to blow cold
air, replace heating element.
Dryer air too hot.
Excessive lint / debris build up
See Maintenance and Cleaning Instructions (pg 5)
Dryer air output is too slow.
Excessive lint / debris build up
See Maintenance and Cleaning Instructions (pg 5)
Excessive Noise or Vibration
Loose mounting screws.
Confirm dryer is securely mounted to wall and motor mounts to
dryer base are tight and secure.
Foreign material in fan housing or
dryer outlet.
Check and remove any foreign material in fan housing or dryer
outlet air slot.
