background image

 

13 

 

Version 1, 15 June 2020, 13 of 16 

12.0  

APPENDIX 

Galvin Engineering Thermostatic Mixing Valve or 
Tempering Valve Commissioning Report and/or 
Maintenance Report

 

Note: 

1.  

Please use a separate form for each valve. 

2. 

The original copy of the report is to be given to the owner/occupier and retained on site for a minimum of 7 years. 

Cross off appropriate box  

 

Thermostatic Mixing Valve 

 

 

Tempering Valve 

 

 

Commissioning Report   

 

 

Maintenance Report  

 

Name of Establishment:    ____________________________________________________________________  

Address of Establishment: ______________________________________________________________________ 

Phone Number: _____________________________ Date: _____________________  Work Order #:  _______  

Contact Person: _______________________  Make & Model of Hot Water System: ________________ ______ 

Temperature of Hot Water to the Valve: ____________ Temperature of Cold Water to the Valve: ______________ 

Hot Water Pressure: ________kPa Cold Water Pressure: _______kPa 

Make of Mixing Valve: _______________________ Model No: ________________________ Size:  _________  

Valve Location/Building:  _____________________________________________________________________  

Valve Identification No:  ______________________________________________________________________  

Total No of Valves on the Site/Building:  _________________________________________________________  

No of Outlets Serviced by this Valve: Baths (    )   Basins (    )  Showers (    ) 

Other Outlets - Details   ______________________________________________________________________  

Valves Installed to the requirements of:

 

The NSW Code of Practice Plumbing and Drainage 

Yes 

No 

The HOSPLAN Code of Practice for Thermostatic Mixing Valves in Health Care 
Facilities 

Yes 

No 

The Valves manufacturers requirements 

Yes 

No 

AS4032.3 

Yes 

No 

The specifications and drawings for the project 

Yes 

No 

The Local Water Supply or Authority 

Yes 

No 

 

If No, give details and actions taken: 
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
______________________________

 

Содержание CliniMix Lead Safe TMV SS

















Отзывы: