background image

S E N D

R E T U R N

T U N E R

F T .   S W I T C H

E Q

G N D

  A C   I N P U T

  12 0 V / 6 0 H z

  5 8 0 W

GND
LIFT

PRE

POST

  F U L L   P O W E R

F X

D I R E C T   O U T

P A T C H   B A Y

LINE OUT/CHAIN OUT (2)

H E A D P H O N E S   ( 1 )

S P E A K E R

500 WATTS @ 4 OHMS

CLASS 2 WIRING

1

2

2

3

4

5

6

7

8

9

1

10

11

2

3

4

5

6

7

11

8

1

MB 500

7

9

10

AC Receptacle:

  The detachable power cord 

plugs in here.

Ground Lift:

 This switch disconnects the 

ground of the balanced, XLR output to eliminate 

hum and buzz when connecting to equipment 

that is running on a different ground system.

Balanced Direct Out:

 This electronically 

balanced output allows a direct connection to a 

P.A. system.

Pre/Post EQ Button: 

This  button switches the 

direct out signal to be before or after the EQ.

Foot switch Input:

 A foot switch is provided to 

engage Boost and Master B modes.

Tuner Output:

 This output comes directly off of 

the input stage and can be patched to a tuner 

using a shielded patch cord. This output is 

unaffected by the Tuning Mute Feature.

Return:

 This input allows the signal from 

outboard effects devices to be inserted before the 

boost section.

Send:

 This output allows signal from the preamp 

to be fed to outboard effects devices from a point 

after the EQ section.

Headphone/Line out/Chain out: 

When 

switched,

 

this output allows the user to send a 

direct (unbalanced) line out to devices with 

unbalanced inputs such as personal multitrack 

recorders. This connection requires a shielded 

patch cord. The Chain out allows the user to 

connect directly to a GK MBP powered 

extension cabinet. This connection is made with 

a balanced, tip, ring, sleeve to male XLR cable.

Unswitched, this headphone jack can be used to 

monitor your playing with headphones.

Headphone/Line out/Chain Out switch: 

This 

switch toggles the output from headphone to line 

out.

Speaker:

 Power amp output to speaker cabinet. 

Delivers 500w into 4 Ohm loads. Lower  

impedances such as 8 Ohms or 16 Ohms and no 

load are acceptable. One 4 Ohm speaker and one 

8 Ohm speaker is not recommended. Use a two 

conductor or the GK 4 conductor Speakon cable 

only.

tip ring sleeve

male XLR

Rear Panel Features

Rear Panel Features

Содержание MB Fusion 800













Отзывы: