Galaxy Control Systems 635 Series Скачать руководство пользователя страница 59

Страница: 59 / 212

635-SERIES HARDWARE M ANUAL

Chapter-Page

2-14

STEP 3. Install Power Connectors inside Controller

Step-3 is about wiring the

two-piece orange connectors

to the wiring harness inside the panel.

WARNING: DO NOT short the power wires together.

Failure to properly insulate wires could

result in damage to the equipment or electrical shocks.

3.1 Remove Heat Shrink (only from wires to be used)

Remove the heat shrink ONLY from the wires for the slots you will use.

The wiring harness inside

the controller is designed to be modular and flexible. Installer can use some or all of the available

slots.

Leave the heat/shrink on the unused wire-tips where no board is installed

or place the proper end-

caps according to your local codes. DO NOT SHORT POWER WIRES.

Figure 10 – Controller Wiring Harness:

This diagram shows the wiring harness inside the Controller prepped for installing boards.

Содержание 635 Series





















































































































































































































Результаты поиска

Содержание 635 Series

Отзывы:

Похожие инструкции для 635 Series

Бренды по названию

Популярные бренды

Galaxy Control Systems 635 Series, Руководство по установке и настройке

Результаты поиска

Содержание 635 Series

Отзывы:

Похожие инструкции для 635 Series

Бренды по названию

Популярные бренды