Gaggia Milano CLASSIC RI9380, Руководство по эксплуатации

Страница: 27 / 33

ENGLISH
27
3. Open the steam/hot water knob ( Fig .1-7) slowly
by turning it counter
-
clockwise
.
4
.
Press the brew button
(
Fig
.1-1)
and the steam
button ( Fig .1-3).
5. Dispense the whole water tank content thro
니
gh
the steam wand .
6. To stop dispensing , press the brew button
(
Fig
.1-1)
and the steam button
(
Fig
.1-3)
again
.
7.
Close the knob
(
Fig
.1 -7)
by Uirning it clockwise
.
8
.
Fill the water tank with fresh drinking water
( Fig -2).
9
.
Insert the filter holder into the brew unit from
the bottom
,
aligning the reference mark on
the filter holder handle with the
(•)
icon on
the front panel of the machine ( Fig .3). Turn the
filter holder from left to right until it locks into
place on the
(▼)
icon
(
Fig
.4).
10. Place a suitable container under the filter
holder
.
11
.
Press the brew b
니
tton
(
Fig
.1-1)
and dispense
all the water in the tank .
12
.
Once the water tank is empty , stop dispensing
by pressing the brew button again
(
Fig
.1-1)
and
empty out the container .
13
.
Remove the filter holder from the unit by
turning it from right to left and rinse it with
fresh drinking water .
14
.
The machine is now ready for
니
se .
Brewing an espresso
니
sing ground coffee-----
The filter holder supplied features the "crema
perfetta
"
filter to prepare one or two coffees
.
Warning! If the Mcrema perfetta " filter is used
without the frothing jet device
,
the machine will
squirt out the coffee , which may result in burns .
Note. If you prefer to use the traditional filter
(Fig.6/7), remove both the "crema perfetta" filter
(Fig.5) and the frothing jet device (Fig.1-16).
To brew the first coffee, it is necessary to preheat
the filter holder first (Fig.1-17):
1. Insert the filter holder (Fig.1 -17) into the brew
unit (Fig.1-8) from the bottom, aligning the
reference mark on the filter holder handle with
the (•) icon on the front panel of the machine
(Fig.3). Turn the filter holder from left to right
until it locks into place on the (▼) icon (Fig.4).
2. Place a large cup
니
nder the filter holder (Fig.1-
17) and press the brew button (Fig.1-1)
3
.
After the cup of water has been filled (about
150cc), press the brew button again and wait
a few minutes for the machine to reach the
correct temperature with the filter holder
inserted.
Note. Any residual water inside the filter holder
must be removed before filling the filter with
ground coffee.
Continue preparing the espresso
4
.
Remove the filter holder (Fig.1-17) and fill it
with ground coffee
니
sing the measuring scoop
provided with the machine (Fig.1-20).
Add one meas
니
ring scoop of coffee for each
cup.
Note. It is recommended to ask roasting
companies for finely ground coffee suitable for
use in coffee machines or to purchase it from
large retailers.
5. Press the coffee using the dedicated tamper
(Fig.1-21). The coffee must be pressed evenly
to obtain a well levelled and flat surface.
6. Remove any coffee residues from the edge of
the filter holder (Fig.1-17).
7
.
Insert the filter holder (Fig.1-17) into the brew
unit (Fig.1-8) from the bottom, aligning the
reference mark on the filter holder handle with
the (•) icon on the front panel of the machine
(Fig.3). Turn the filter holder from left to right
until it locks into place on the (▼) icon (Fig.4).
8
. Wait
니
ntil the indicator light turns on (Fig.1 -5).
9
.
Press the brew button (Fig.1-1).
10
.
When the cups are 3/4 full, press the brew
button again (Fig.1-1).
The coffee will be m
아
e or less intense
depending on the amount of water used and,
if prepared following the correct procedure, it
will have the typical haze I nut/brown coloured
"natural cream".