Gaggenau VI 482 103, Инструкция по эксплуатации

Страница: 24 / 36

24
en
Home Connect
Manual registration in the home network
Note: To log in to the WiFi manually, you require the
network name (SSID) and password (key) for your home
network.
1 Wait for two minutes until the illuminated ring on
the control knob flashes red once and
’‹¯ ƒ
lights up on the control panel.
The appliance is now in manual mode.
2 Switch to the general settings menu of your mobile
device and call up the WiFi settings.
The "Home Connect" WiFi connection is available
on your mobile device.
3 Connect to the "Home Connect" (password:
"HomeConnect") WiFi connection.
4 Launch the app on your mobile device and follow
the instructions for automatic network login.
5 The appliance is available in the app on the mobile
device once
Ö
lights up on the control panel and
the illuminated ring on the control knob lights up
green.
Note: If the illuminated ring on the control knob lights
up red, it was not possible to establish a connection to
the WiFi. Check the router and start the connection
process again. Check that you have correctly entered
the password.
Restart the connection process
1 Turn the control knob anti-clockwise to position 0 .
The illuminated ring on the control knob lights up
blue.
2 Turn the control knob clockwise to position
ª
or
¹
.
On the control panel,
••’
and
’‹¯‚
are
displayed alternately. The illuminated ring on the
control knob flashes blue. The hob is now ready for
registration in the WiFi.
Exiting the Home Connect settings menu
1 Carry out the following operating steps one after
the other without interruption.
2 Push in the control knob and turn it anti-clockwise
to the
Ž
position.
3 Turn the control knob clockwise to position
ª
or
¹
.
4 Turn the control knob anti-clockwise to position 0 .
The illuminated ring on the control knob goes out.
Switching WiFi off/on
You can switch off the Wi-Fi on your hob at any time
(e.g. to save energy during a holiday). The connections
to the home network and to the extractor hood remain
saved. When you switch the Wi-Fi back on, the saved
connections are applied.
1 Carry out the following operating steps one after
the other without interruption.
2 Push in any control knob and turn it anti-clockwise
to the
Ž
position.
3 Turn the control knob clockwise to position
ª
or
¹
.
4 Turn the control knob anti-clockwise to position 0 .
The illuminated ring on the control knob lights up
blue.
5 Turn the control knob clockwise to position 1 .
The illuminated ring on the control knob lights up
green.
Ö
lights up on the control panel. After
five seconds, the Wi-Fi is switched off and the
illuminated ring on the control knob lights up blue.
The
Ö
symbol on the control panel goes out.
If you want to switch the WiFi back on, run through the
same operating sequence. The illuminated ring on the
control knob lights up blue. After 5
seconds, the WiFi is
switched on and the illuminated ring around the control
knob lights up green.
Ö
lights up on the control panel.
Resetting connection
You can reset the connections you have saved for your
home network and extractor hood at any time.
1 Carry out the following operating steps one after
the other without interruption.
2 Push in any control knob and turn it anti-clockwise
to the
Ž
position.
3 Turn the control knob clockwise to position
ª
or
¹
.
4 Turn the control knob anti-clockwise to position 0 .
The illuminated ring on the control knob lights up
blue.
5 Turn the control knob clockwise to position 2 .
¥“†
lights up on the control panel. After
30 seconds, the connection is reset and the
illuminated ring on the control knob flashes. The
connection is reset once
š‹¯“
lights up on the
control panel and the illuminated ring on the control
knob lights up green.