background image

5

9

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Electric Safety

9

WARNING

Before you plug in an electrical cord 
or turn on power supply, make sure 
all controls are in the OFF position.

For appliances equipped with a cord and 
plug, do not cut or remove the ground 
prong. It must be plugged into a matching 
grounding type receptacle to avoid 
electrical shock. If there is any doubt as 
to whether the wall receptacle is properly 
grounded, the customer should have it 
checked by a qualified electrician.

If required by the National Electrical 
Code (or Canadian Electrical Code), this 
appliance must be installed on a separate 
branch circuit.

The circuit breaker should have a contact 
separation of at least 3 mm on all poles.

Be sure your appliance is properly 
installed and grounded by a qualified 
technician. Installation, electrical 
connections and grounding must comply 
with all applicable codes.

Before installing, turn power OFF at the 
service panel. Lock service panel to 
prevent power from being turned ON 
accidentally.

Installer – show the owner the location of 
the circuit breaker or fuse. Mark it for 
easy reference.

Gas Safety

Install a gas shutoff valve near the 
appliance. It must be easily accessible in 
an emergency.

Leak testing must be conducted by the 
installer according to the instructions in 
this manual.

The appliance and its individual shutoff 
valve must be disconnected from the gas 
supply piping system during any pressure 
testing at pressures in excess of ½ psi 
(3.5 kPa).

The appliance must be isolated from the 
gas supply piping system by closing its 
individual manual shutoff valve during any 
pressure testing of the gas supply piping 
system at test pressures equal to or less 
than ½ psi (3.5 kPa).

The minimum supply pressure must be 1" 
water column above the manifold 
pressure printed on the data plate.  
The maximum supply pressure must not 
exceed 14.0 inches water column 
(34.9 Millibars).

State of California Proposition 65 Warnings

9

WARNING

This product can expose you to 
chemicals including vinyl chloride, 
which is known to the State of 
California to cause cancer and birth 
defects or other reproductive harm. 
For more information go to 

www.P65Warnings.ca.gov

.

Содержание VG415211CA





















































Отзывы: