Gaggenau BOP2201.2, Руководство пользователя и инструкции по установке

Страница: 46 / 52

en
Installation instructions
46
¡
Install the appliance in accordance with the
installation diagram. Observe the minimum
clearances.
¡
Installation behind cabinet doors: Suitable
measures should be taken to ensure these
types of doors cannot close during opera-
tion. There is a risk of overheating if the
door does not remain open during opera-
tion or during cooling (fan operation).
¡
Before starting up the appliance, remove
any packaging material and adhesive film
from the cooking compartment and the
door.
¡
The dimensions in the figures are in mm.
21.2 Planning notes
Observe the following planning notes before installing
the appliance.
¡
The door direction cannot be reversed.
¡
The distance from the furniture cavity to the door
panel surface is 21 mm.
¡
The distance from the furniture cavity to the outer
edge of the door handle is 72 mm.
¡
Note the overhang for opening drawers next to the
appliance.
¡
When planning a corner solution, consider a door
opening angle of at least 110°.
¡
If you install the appliance under a hob, maintain a
clearance of at least 15 mm between the underside
of the hob and the top of the oven housing. Take
the planning notes of the hobs into consideration,
particularly for the ventilation, gas connection and
the electric connection.
21.3 Appliance dimensions
You will find the dimensions of the appliance here
21.4 Preparing fitted units
Requirement:
Fitted units must be heat-resistant up to
90 °C, and adjacent unit fronts up to 70 °C.
1.
To ventilate the appliance, create a ventilation cut-
out of at least 20 x 500 mm in the intermediate floor
of the fitted cabinet.
2.
Ensure that the mains socket is located outside of
the built-in niche.
3.
Carry out cut-out work on the units and then insert
the appliance.
4.
After making the cut-outs, remove any shavings.
Shavings may impair the function of electrical com-
ponents.
5.
Secure any unsecured units to the wall using a
standard bracket.
6.
Only install the appliance high enough that the cus-
tomer can remove any accessories effortlessly.
21.5 Electrical connection
In order to safely connect the appliance to the elec-
trical system, follow these instructions.
¡
Ensure that there is sufficient fuse protection for the
household wiring. The voltage and frequency of the
appliance must match the electrical installation; see
the rating plate.
¡
The appliance corresponds to protection class I and
must only be operated with a protective earth con-
nection.
¡
Fuse protection by means of B- or C-type circuit
breakers is required.
¡
An all-pole isolating switch with a contact gap of at
least 3 mm must be fitted during installation. This
must remain accessible after installation.
¡
Appliances without a power cable must only be con-
nected in accordance with the connection diagram.
If required, install the enclosed copper bridges.
The appliance may be damaged if it is not connec-
ted correctly.
¡
The power cable must correspond to type H05 VV-F
or a higher rating.
¡
The yellow/green wire for the PE connection must
be 10 mm longer than the other wires for the appli-
ance.
¡
To achieve the 550 mm installation depth, the con-
nection cable needs to follow the slanted edge on
the lower right hand corner of the housing.
21.6 LAN connection to the home network
This appliance can be networked. You can connect the
appliance to the home network using a LAN cable. The
scope of delivery does not include a LAN cable.
Establishing the LAN connection
1.
Before installing the appliance, insert a LAN cable
into the socket on the back of the appliance.
2.
Use the strain relief to secure the LAN cable in
place.
3.
Connect the LAN cable to a network connection.