background image

PISTON ROD ASSEMBLY

 745244

SPRING - 50806

RETAINING RING - 400936

O'RING - A-287

BACK - UP RING - 401101

DESCRIPTION

The GBP712C is a pneumatic-hydraulic tool designed specifically for the efficient installation of a wide
range of blind rivets and lockbolts.  It weighs 6.5 lbs. and can be operated in any position with one hand.
It has a .775" rivet setting stroke and a rated pull load of 4500 pounds with 90 psi air pressure at the air
inlet.

The GBP712C riveter operates on a wide range of air pressure, with 90 to 100 psi providing the maximum
efficiency.  At 90 lbs. air pressure, the GBP712C does not exceed 85 db (A) and consumes 3.9 cfm at 20
cycles per minute.

The air inlet is provided with 1/4-18 female pipe threads for accepting the user's air hose fitting. 

NOSE ASSEMBLIES ARE NOT FURNISHED WITH THIS TOOL ORDER SEPARATELY (SEE PAGE 8).

      

MAINTENANCE

The performance of any tool depends upon good maintenance practices.  Following these minimal
requirements for service and care will extend the life of your tool.
  *Only use an air supply set at 90-120 lbs. equipped with a filter-regulator to prevent  wear.
  *The tool will eventually lose some hydraulic oil. Keep the hydraulic system full and free of air by         
   using the air bleeder (745163) on a regular basis.
  *Proper care by operator is necessary in maintaining full productivity and reducing downtime.  Read   
   all applicable tool manuals and nose assembly data sheets prior to operating tools.

  

*Keep nose assemblies, especially jaws, clean and free of chips and debris.

  *For a complete overhaul, tool kit GBP745CTK is recommended.

TORQUE SPECIFICATIONS

Button Head Cap Screws (402479) = 40 inch lbs.
Packing Plug (744118) = 45 foot lbs.
Flexlock Nut (400559) = 40 inch lbs.

WARNING

This tool incorporates a patented hydraulic relief valve. When overhauling tool, o’ring (A-287), back-up ring
(401101), retaining ring (400936) and spring (50806) must be replaced. Failure to do so could rerr
sult in SEVERE PERSONAL INJURY!

4

Содержание GBP712C











Отзывы: