manualshive.com logo in svg

Gage Bilt GB751SH-5, Оригинальное руководство пользователя

Поделиться
Скачать
Gage Bilt GB751SH-5 Скачать руководство пользователя страница 15

15

 

9/17

 

GB751SH

-

5 INSTALLATION TOOL

 

 

REMOVING 704130 ACTUATOR ASSY

-

AIR 

 

 

 

1.

 

Remove actuator lever assy (704343) including pin

-

slotted (400608).

 

2.

 

With actuator lever assy (704343) removed, insert a 5/8” open end box wrench around 
actuator assy

-

air (704130).

 

3.

 

Loosen the actuator assy

-

air (704130).

 

4.    Remove wrench. Unthread and remove the actuator assy

-

air (704130) with fingers from the 

 

handle

-

split (700323). 

 

INSTALLING 704130 ACTUATOR ASSY

-

AIR 

 

 

 

1.

 

Apply Teflon® tape onto threads of actuator assy

-

air (704130) one to two wraps.

 

2.

 

Thread the actuator assy

-

air (704130) all the way into handle

-

split (700323) with fingers.

 

3.

 

Insert and turn 5/8” open end box wrench and snug tight approximately 1/4

-

1/2 turn.

 

4.

 

Re

-

attach the actuator lever assy (704343) with pin

-

slotted (400608).

 

Image may not 
reflect actual tool.

 

ACTUATOR ASSY

-

AIR

 

WARNING

: 

Disconnect tool from its power source before actuator removal or installation. Severe personal injury may occur if 

 

power source is not disconnected.

 

 

 

CAUTION:  

Actuator assy

-

air (704130) can break if not careful.

 

 

CAUTION:  

Do not over tighten actuator assy

-

air (704130). Snug tighten only.

 

OVERHAUL

 

Содержание GB751SH-5

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды