![background image](http://html.mh-extra.com/html/gage-bilt/gb745sh-5/gb745sh-5_original-instructions-manual_555944012.webp)
12
REV. 6/22
GB745SH
-
5 INSTALLATION TOOL S/N: 1046 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
BLEEDING PROCEDURE:
WARNING:
Do not cycle tool without air bleeder assembly (704153), or the screw and stat
-
o
-
seal, installed in tool head. Severe
personal injury could result.
WARNING:
Use CAUTION when removing screws, air bleeder assembly (704153) and fill bottle (745263). Hydraulic oil may be
under pressure.
CAUTION:
Before filling handle assembly (744129), air piston assembly (744121) must be all the way down.
CAUTION:
When forcing piston rod assembly (745344) downward, with head cylinder (745366) removed, hydraulic oil will eject forcibly
from handle assembly (744129).
CAUTION:
When bleeding tool, ensure tubing is free from kinks or other obstructions.
IMPORTANT:
Be sure to use thread sealant on all hydraulic fittings, Loctite® 545 or equivalent or a non
-
hardening Teflon® thread
compound such as Slic
-
tite®. Tighten until fitting feels snug and then continue to tighten 1/2 to 1 full turn.
CAUTION:
Over tightening
can easily distort the threads. DO NOT USE TEFLON® TAPE.
CAUTION:
Teflon® tape is an excellent thread sealer, however, if it is
not properly applied, pieces of Teflon® may enter the hydraulic system and cause malfunction or damage.
1. Stand handle assembly (744129) on floor, stretch hose and head assembly upward and lay flat on a table or bench. When bleeding
tool always keep the head assembly higher than the handle assembly.
2.
For
“
PULL
”
pressure only:
Attach air bleeder assembly to side hole of manifold
-
handle (745303) hole marked
“
P
”
in an upright position.
3. Connect the tool to air supply and cycle tool ten times holding the actuator assembly
-
air (704130) down for 2
-
3 seconds between
cycles to remove any air from the tool. Leave piston (745310) in FRONT position (Dim
“
A
”).
4. Disconnect air supply. Remove air bleeder assembly from side hole of manifold
-
handle (745303) hole marked
“
P
”
and replace
with button head cap screw (402482) and stat
-
o
-
seal (S572). Torque 35 inch lbs. (3.95 Nm). Do not over tighten.
5. Remove button head cap screw (402482) and stat
-
o
-
seal (S572) from head cylinder (745366) side hole (marked #1) and attach air
bleeder assembly in an upright position.
6. Connect air supply. Cycle tool ten times removing any air bubbles. Leave piston (745310) in FRONT position (Dim
“
A
”).
7.
Disconnect air supply. Remove air bleeder assembly from side hole (marked #1) on head cylinder (745366) and replace button
head cap screw (402482) and stat
-
o
-
seal (S572). Torque to 35 inch lbs. (3.95 Nm). Do not over tighten.
8.
Attach air supply, press and hold actuator lever assembly (704343) leaving piston (745310) in REAR position (Dim
“
B
”)
then
disconnect air supply.
9.
For
“
RETURN
”
pressure only:
Attach air bleeder assembly to side hole of manifold
-
handle (745303) hole marked
“
R
”
in an upright position.
10. Connect the tool to air supply and cycle tool ten times holding the actuator assembly
-
air (704130) down for 2
-
3 seconds between
cycles to remove any air from the tool. Press and hold actuator lever assembly (704343) leaving piston (745310) in REAR position (Dim
“
B
”)
.
11. Disconnect air supply. Remove air bleeder assembly from side hole of manifold
-
handle (745303) hole marked
“
R
”
and replace
with button head cap screw (402482) and stat
-
o
-
seal (S572). Torque 35 inch lbs. (3.95 Nm). Do not over tighten.
12. Remove button head cap screw (402482) and stat
-
o
-
seal (S572) from head cylinder (745366) side hole (marked #2) and attach
air bleeder assembly in an upright position.
13. Connect air supply. Cycle tool ten times removing any air bubbles. Leave piston (745310) in REAR position (Dim
“
B
”).
14. Disconnect air supply. Remove air bleeder assembly from side hole (marked #2) on head cylinder (745366) and replace button
head cap screw (402482) and stat
-
o
-
seal (S572). Torque to 35 inch lbs. (3.95 Nm). Do not over tighten.
15.
Connect air supply. Cycle tool five times and check stroke of
.620” (15.75
mm). We recommend using calipers. With the actuator
lever assembly (704343) released, check dimension (A). While holding actuator lever assembly (704343) in, check dimension (B).
Subtract dimension (A) from dimension (B). If stroke is not consistent within 1/64" (.396 mm) repeat bleeding steps 2
-
15 until
stroke met. For your consideration, Gage Bilt offers a depth gage (Pt.# A
-
1935) to help simplify and more accurately check your tool
stroke. Please contact Gage Bilt for more information.
Note:
•
Air Bleeder Assembly (704153) (sold separately) is required.
* FILLING & BLEEDING VIDEO AVAILABLE AT:
http://www.gagebilt.com/rivet_tools_videos.php
BUTTON HEAD CAP SCREW (402482) &
STAT
-
O
-
SEAL (S572) (BLEEDER HOLE #1)
BUTTON HEAD CAP SCREW (402482) &
STAT
-
O
-
SEAL (S572) (BLEEDER HOLE #2)
Hole marked
“
R
”
on rear of
Manifold
-
Handle (745303
)
Hole marked
“
P
”
on side of
Manifold
-
Handle (745303)
Air Bleeder
Assembly
(704153)
Images may not
reflect actual tool.