Gage Bilt GB745 Скачать руководство пользователя страница 14

Страница: 14 / 24

Rev. 6/22

GB745 INSTALLATION TOOL S/N: 3569 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

TROUBLESHOOTING

Providing all maintenance conditions have been met, follow this systematic approach to diagnosis.

1. MORE THAN ONE PULL IS REQUIRED TO BREAK FASTENER.

Tool needs to be bled. (See filling and bleeding procedure pgs. 11

12).

Spring has fatigued, replace.

Jaws are stripped or packed with chips. Clean or replace.

Incorrect nose tip.

2. SLOW OR PARTIAL OPERATION WHEN THE ACTUATOR ASSEMBLY

AIR (704130) IS DEPRESSED.

’

Ring (403815) and Back

Up Rings (401119) on piston (745310) could be worn or damaged. Replace.

Back

Up Rings (S908) and O

’

Ring (A

201) on piston rod assembly (745344) could be worn or damaged. Replace.

Muffler (744143) or filter inside Valve Spool Assembly (743142) may be plugged with dirt. Clean thoroughly and back

blow

with compressed air.

Hole in metering screw in valve spool assembly (743142) may be blocked or damaged. Hole diameter should be .028" (.71 mm).

Clear and size or replace.

3. NO OPERATION WHEN ACTUATOR ASSEMBLY

AIR (704130) IS DEPRESSED.

Tool seized due to mechanical failure or damaged parts.

4. OIL LEAKAGE.

DO NOT

OPERATE WITH OIL LEAKING FROM TOOL. HIGH PRESSURE OIL MAY CAUSE SEVERE PERSONAL INJURY.

Any oil leaking externally should be traced to its source. An o'ring or seal that leaks should be replaced.

5. AIR BYPASS FROM VALVE HOUSING.

If the spring (744144) breaks or dislodges, air will flow freely through the muffler (744143). Replace or reset. Valve spring

installation tool (744251) is recommended.

Check o'rings on valve sleeve (743144), valve spool assembly (743142), and valve plug (744142). If worn or damaged, re-

place. Valve sleeve removal tool (744152) is recommended.

6. FASTENER STEM JAMMED IN NOSE ASSEMBLY.

Nose assembly components require service.

DISCONNECT AIR FROM TOOL

, remove the nose from the tool and

disassemble. Replace worn or broken parts. Clean the surface the jaws ride on.

Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble.

Incorrect follower.

REMOVING ACTUATOR ASSEMBLY

AIR (704130)

Remove actuator lever assembly (704343) including pin

slotted (400608) from

handle assembly (744129).

Insert a

5/8”

open end / adjustable wrench around actuator assembly

air (704130).

Loosen the actuator assembly

air (704130).

Remove wrench. Unthread and remove the actuator assembly

air (704130) with

fingers from the handle assembly (744129).

INSTALLING ACTUATOR ASSEMBLY

AIR (704130)

Apply Teflon® tape onto threads of actuator assembly

air (704130) one to two wraps.

Thread the actuator assembly

air (704130) all the way into handle assembly (744129) with

fingers.

Insert and turn

5/8”

open end / adjustable wrench and snug tight approximately 1/4

1/2 turn.

attach actuator lever assembly (704343) including pin

slotted (400608) to

handle assembly (744129).

ACTUATOR ASSEMBLY

AIR

OVERHAUL

WARNING

Disconnect tool from its power source before actuator removal or installation. Severe personal injury may occur if

power source is not disconnected.

CAUTION:

Actuator assembly

air (704130) can break if not careful.

CAUTION:

Do not over tighten actuator assembly

air (704130). Snug tighten only.

Содержание GB745

























Результаты поиска

Содержание GB745

Отзывы:

Похожие инструкции для GB745

Бренды по названию

Популярные бренды

Gage Bilt GB745, Инструкция по эксплуатации

Результаты поиска

Содержание GB745

Отзывы:

Похожие инструкции для GB745

Бренды по названию

Популярные бренды