background image

                                            4

 

REV 3/23

 

 

GB743SHAVT

 

 

SPECIFICATIONS

 

 

Hand Held Weight

 

-

   3.50 lbs. (1.6 kg)

 

Air pressure req'd

 

-

   90 

-

 100 p.s.i. (6.2 

-

 6.9 bar)

 

Hyd. Power Source

 

-

   GB808V series

 

Hydraulic oil

 

-

   See powerunit for hydraulic oil specifications 

 

Setting stroke

 

-

   .900" (22.86 mm)

 

Rated pull load

 

-

   4,000 lbs. 

 

 

The GB743SHAVT is a pneumatic

-

hydraulic split handle installation tool designed specifically for the efficient installation of blind 

rivets. This tools unique "split" system provides the operator with a lightweight ergonomic tool. The handle and head assembly when 

held in hand weighs 3.5 lbs. (1.6 kg).

 

 

 

 

 

 

 

 

 

 

The GB743SHAVT pneumatic

-

hydraulic split handle installation tool operates in conjunction with the GB808V series.

 

 

The GB743SHAVT comes with 8ft. (2.4 m) of hose. 

 

 

THE GB743SHAVT IS SOLD FASTENER SPECIFIC. (SEE NOSE ASSEMBLY SELECTION CHART ON PAGE 17 TO PULL ANY FASTENERS 

OTHER THAN WHAT TOOL WAS PURCHASED FOR). 

 

DESCRIPTION 

 

 

WARNING

Any other use is forbidden. 

 

ENVIRONMENTAL USE

 

 

WARNING

Do not operate in an explosive atmosphere. 

 

 

The GB743SHAVT can be operated between 0ºF 

-

 118ºF (

-

17.8ºC / 47.8ºC)

 

Содержание GB743SHAVT

























Отзывы: