background image

13 

REV. 10/14 

 

S/N: 2269 AND ABOVE  

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. 

DEXRON® IS A REGISTERED TRADEMARK OF GENERAL MOTORS CORPORATION. LUBRIPLATE® IS A REGISTERED TRADEMARK OF FISKE BROTHERS REFINING CO. LOCTITE® IS A REGISTERED 
TRADEMARK OF HENKEL CORPORATION. 

 

Seller warrants that all goods covered by this catalog will conform 

to applicable specifications and will replace or repair, F.O.B. our plant, any 
goods  providing  defective  from  faulty  workmanship,  or  material,  for  6 
months from date of shipment

.  

 

Said  warranty  to  remain  in  effect  if,  and  only  if,  such  goods  are 

used in accordance with all instructions as to maintenance, operation and 
use, set forth in manuals and instruction sheets furnished by seller. 
 

Sellers obligation under this warranty shall be limited to the repair 

or rework of the goods supplied or replacement thereof, at Seller’s option, 
and  in  no  case  is  to  exceed  the  invoice  value  of  said  goods.  Under  no 
circumstances  will  the  seller  be  liable  for  incidental  or  consequential 
damages  or  for  damages  incurred  by  the  buyer  or  subsequent  user  in 
repairing  or  replacing  defective  goods  or  if  the  goods  covered  by  this 
warranty are reworked or subjected to any type of additional processing. 
 

This  warranty  is  void  if  Seller  is  not  notified  in  writing  of  any 

rejections or defects within 6 months after the receipt of the material by the 
customer. 

THIS  WARRANTY  IS  MADE  IN  LIEU  OF  ALL  OTHER  WARRANTIES 
EXPRESSED OR IMPLIED, INCLUDING MERCHANTABILITY. 

 

WARRANTY 

 
 
 

DECLARATION OF CONFORMITY 

MANUFACTURER:

 Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan (586-226-1500) 

 

WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS  

TO THE FOLLOWING DIRECTIVES AND STANDARDS  

 

Machinery Directive 2006/42/EC

 

 

EN12100-1 & EN12100-2 

EN792-1:2000+A1 

 

EU REPRESENTATIVE

Edgar Hausmann GmbH

 

Förster-Busch-Str. 10

 

D-34346 Hann. Münden Germany  

 

EQUIPMENT DESCRIPTION: 

GB743 FASTENER INSTALLATION TOOL 

 

This procuct specified above conforms to the above dIrectives and standards. 

 

 

 

 

 

SIGNATURE: 

 
 

NAME:  BRIAN LEIGH 

 

 

 

 

 

         

 PRODUCT MANAGER 

 

 

 

 

 

         

 CLINTON TWP., MI U.S.A. 

 

 

 

 

 

 

 

 MAY 2010 

 

 

 

 

 

 

 

 (586) 226-1500 

GAGE BILT 

Содержание GB743














Отзывы: