11
REV 6/22
GB731OSSH INSTALLATION TOOL
FILLING PROCEDURE
WARNING:
Do not cycle tool without air bleeder assembly (704153), or the screw and stat
-
o
-
seal, installed in tool head. Severe
personal injury could result.
WARNING:
Use CAUTION when removing screws, air bleeder assembly (704153) and fill bottle (745263). Hydraulic oil may be under pressure.
CAUTION:
Before filling handle assembly (722132), air piston assembly (704121) should be all the way down.
CAUTION:
When forcing piston rod assembly (731333) downward, with head cylinder assembly (731912) removed, hydraulic oil will
eject forcibly from handle assembly (722132).
CAUTION:
When bleeding tool, ensure tubing is free from kinks or other obstructions.
IMPORTANT:
Be sure to use thread sealant on all hydraulic fittings, Loctite® 545 or equivalent or a non
-
hardening Teflon® thread
compound such as Slic
-
tite®. Tighten until fitting feels snug and then continue to tighten 1/2 to 1 full turn.
CAUTION:
Over tightening
can easily distort the threads. DO NOT USE TEFLON® TAPE.
CAUTION:
Teflon® tape is an excellent thread sealer, however, if it is not
properly applied, pieces of Teflon® may enter the hydraulic system and cause malfunction or damage.
1.
Ensure air piston assembly (704121) is at the bottom of stroke by pushing piston rod assembly (731333) all the way down.
2. Fill power cylinder (731237) and oil passage (c
’
bored hole for o
’
ring (S832) with Automatic Transmission Oil, Dexron® III or equivalent.
3. Place gasket (745124) and o
’
ring (S832) on top of handle assembly (722132).
4. Press manifold
-
handle (730303) down on power cylinder (731237) and install four button head cap screws (A
-
928) evenly. Apply
Loctite® 242 and torque to 40 inch pounds (4.52 Nm).
5. Attach hydraulic hoses (A
-
1437) to manifold
-
handle (730303).
(See hydraulic thread preparation pg. 10).
6. Install barbed fitting (S1181) to manifold
-
handle (730303) and attach air line (704311) and hose clamp (A
-
144) and tighten.
7. Slide hose guard (703561) over both hydraulic hoses (A
-
1437) and air line (704311).
8. Push piston (731904) in head cylinder assembly (731912) to rear until you achieve .350" (8.9 mm) (see
”
B
”
dim on pg. 12) from full
forward position. Stretch entire tool out in a horizontal position across table or floor.
9. Attach handle
-
split (700326) to air line (704311) and secure handle
-
split (700326) to hydraulic hoses (A
-
1437).
(See hydraulic thread
preparation pg. 10).
10. Remove button head cap screw (402482) and stat
-
o
-
seal (S572) from hole stamped
“
P
”
on manifold
-
handle (730303) and front hole
on head cylinder assembly (731912). Attach fill bottle (745263) to hole, side stamped
“
P
”
on manifold
-
handle (730303).
11. Pump oil into head cylinder assembly (731912) by squeezing fill bottle (745263) located at handle
-
split (700326) until oil comes out
of front hole on head cylinder assembly (731912). Replace button head cap screw (402482) and stat
-
o
-
seal (S572) on front hole of
head cylinder assembly (731912). Remove fill bottle (745263) and replace button head cap screw (402482) and stat
-
o
-
seal (S572) on
manifold
-
handle (730303) and torque both 35
-
40 inch lbs. (3.95
-
4.52 Nm). Do not over tighten.
12. Remove button head cap screw (402482) and stat
-
o
-
seal (S572) from hole stamped
“
R
”
on manifold
-
handle (730303) and rear hole
on head cylinder assembly (731912). Attach fill bottle (745263) to hole, side stamped R, on manifold
-
handle (730303).
13.
Pump oil into head cylinder assembly (731912) by squeezing fill bottle (745263) located at handle
-
split (700326) until oil comes out
of rear hole of head cylinder assembly (731912). Replace button head cap screw (402482) and stat
-
o
-
seal (S572) on rear hole of
head cylinder assembly (731912). Remove fill bottle (745263) and replace button head cap screw (402482) and stat
-
o
-
seal (S572)
on manifold
-
handle (730303) and torque both to 35
-
40 inch lbs. (3.95
-
4.52 Nm). Do not over tighten.
14.
Proceed to bleeding procedure on pg. 12 to remove air from hydraulic system.
Images may not reflect actual tool
* FILLING & BLEEDING VIDEO AVAILABLE AT:
http://www.gagebilt.com/rivet_tools_videos.php
Oil Passage hole
O
’
ring (S832)
Power Cylinder hole
***Keep air hole
free from oil***
Fill Bottle (745263)
Front and Rear bleeder holes on
head cylinder assembly (731912).
Button head cap screws (402482)
& stat
-
o
-
seals (S572).
Note:
•
Fill Bottle (745263) (sold separately), is required.
