11
7/11 REV 5/22
GB713 Installation Tool
WARNING:
Do not cycle tool without air bleeder assembly (704153), or the screw and stat
-
o
-
seal, installed in tool head. Severe
personal injury could result.
Use CAUTION when removing screws, air bleeder assembly (704153) and fill bottle (745263). Hydraulic oil may be
under pressure.
CAUTION:
Before filling handle assembly (744129), air piston assembly (744121) must be all the way down.
CAUTION:
When forcing piston rod assembly (744136) downward, with head cylinder assembly (713121) removed, hydraulic oil will
eject forcibly from handle assembly (744129).
CAUTION:
When bleeding tool, ensure tubing is free from kinks or other obstructions.
FILLING & BLEEDING VIDEO AVAILABLE AT:
http://www.gagebilt.com/rivet_tools_videos.php
BLEEDING PROCEDURE:
To replace a small amount of oil,
DISCONNECT AIR FROM TOOL
. Remove button head cap screw (402482) and stat
-
o
-
seal (S572)
from head cylinder assembly (713121). Install air bleeder assembly (704153) and connect tool to air line. Cycle ten times to fully
circulate oil through hydraulic system.
DISCONNECT AIR FROM TOOL
, remove the air bleeder assembly(704153), and reinstall button
head cap screw (402482) and stat
-
o
-
seal (S572) on head cylinder assembly (713121). Torque 35
-
40 inch lbs. (3.95
-
4.52 Nm). Do not
over tighten. This will ensure the removal of any air from the hydraulic system and its replacement with oil.
FILLING AND BLEEDING PROCEDURE: (
required after tool has been dismantled)
1.
Place piston rod wench assembly (704149) in power cylinder (743131) and carefully push piston rod assembly (744136) and air
piston assembly (744121) completely down.
2. Fill handle assembly (744129), power cylinder (743131) and the oil passage on top of handle assembly (744129) with automatic transmission
oil, Dexron® III or equivalent. When looking at the top of the handle assembly (744129), the oil passage is the hole that is counterbored for
o'ring (S832). See image below.
3. Push piston (713211) full forward in head cylinder assembly (713121), then attach head cylinder assembly (713121) with care,
ensuring gasket (704129) and o'ring (S832) are properly installed. Apply Loctite® 242 to button head cap screws (402479) and
torque uniformly to 40 inch lbs. (4.52 Nm) to prevent leakage around gasket (704129).
4.
ENSURE TOOL IS DISCONNECTED FROM AIR.
Remove button head cap screw (402482) and stat
-
o
-
seal (S572) from head cylinder
assembly (713121). Install air bleeder assembly (704153) and connect tool to air line. Cycle ten times to fully circulate oil through
hydraulic system.
5.
DISCONNECT AIR FROM TOOL
. Remove air bleeder assembly (704153) and install button head cap screw (402482) and stat
-
o
-
seal
(S572) on head cylinder assembly (713121). Torque 35
-
40 inch lbs. (3.95
-
4.52 Nm). Do not over tighten.
6.
Reconnect air and cycle tool 10 more times. Check tool stroke using instructions a thru c and diagrams below. We recommend
using dial calipers.
a.
With the actuator assembly
-
air (704130) released check dimension (A).
b. Holding actuator assembly
-
air (704130) in, check dimension (B).
c. Subtract dimension (A) from dimension (B). If stroke doesn
’
t check .760" (19.3 mm) min. (See figures below) follow
bleeding procedure above.
For your consideration, Gage Bilt offers a depth gage (Pt.# A
-
1935) to help simplify and more accurately check your tool stroke.
Please contact Gage Bilt for more information.
FILLING AND BLEEDING PROCEDURE:
Images may not reflect actual tool.
Bleeder hole on head cylinder assembly
(713121). Button head cap screw
(402482) & stat
-
o
-
seal (S572)
Note:
•
Air Bleeder Assembly (704153) is required.
Oil Passage hole
O
’
ring (S832)
Handle Assembly and
Power Cylinder hole
***Keep air
hole free
from oil***
Air Bleeder
Assembly
(704153)
