G.R.A.S. 12AQ Скачать руководство пользователя страница 7

Страница: 7 / 22

Overload

LED: on when

overload present; off

when absent, unless

latched to remain on

after overload.

Filter

switch: rotate switch

to make a selection.

CCP Input

Floating Ouput

Polarization 0 V

buttons: LED on only

when function is active,

otherwise off.

Gain

LEDs: showing the selected

gain in dB. Rotate switch

clockwise to increase gain and

vice-versa

SysCheck

button: LED

on when SysCheck

active, otherwise off.

On/Off button

Power

LED: green on; yellow

standby, otherwise

Battery

LED: green on; red low.

Remote

LED: when on (manual

switches disabled, except power).

Channel

numbers.

Filter

LEDs: showing the selected filter.

Lin

(Linear)

(high-pass)

(A-weighted)

Ext

(Extension) optional customised

filter.

Latch

button: LED on

only when Latch is

active, otherwise off *

Preamp . ±15 V

button: LED on only when

value is set to ±15 V,

otherwise it is ±60 V.

G.R.A.S. SOUND & VIBRATION

Power Module Type 12AQ

Page 7

External Features

2 .1 Front Panel

Front-panel details are shown in Fig. 2.1.

2 .1 .1 Manual Control

Manual control is via toggle-buttons and rotary switches. Green LEDs indicate the current set-

tings and red LEDs are overload warnings (

Power

and

Battery

LEDs apart).

With the exception of

Remote

, the Type 12AQ can be manually-controlled via its front panel.

Remote

can be selected only via the RS232 interface. Note: when

Remote

is active, manual

control is disabled (except power off). Only remote control via the RS232 interface is permitted.

Power button

Note: when external power is connected, it will take precedence over battery power.

With external power connected, the

Power

LED shows:

• Yellow for standby
• Green for switched on
With only battery power available, the

Battery

LED shows:

• Green for switched on

• Red for insufficient battery power, only when powered on (see chapter 3 for changing

batteries)

Fig. 2.1

Front-panel details of the Power Module Type 12AQ

* Behaviour modified if the

latch

command has been sent via the RS232 interface.

Содержание 12AQ























Результаты поиска

Содержание 12AQ

Отзывы:

Похожие инструкции для 12AQ

Бренды по названию

Популярные бренды

G.R.A.S. 12AQ, Инструкция по эксплуатации

Результаты поиска

Содержание 12AQ

Отзывы:

Похожие инструкции для 12AQ

Бренды по названию

Популярные бренды