FXConnectX STAGEPRO-8 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 14

FXConnectX STAGEPRO-8 Скачать руководство пользователя страница 4

Copyright 2014 by FXConnectX LLC. All Rights Reserved.

Page 4



PWR: Power On/Off switch



LEARN: The Learn LED is illuminated when the L-SW (Learn Switch) is pressed and
learn mode is active.



MUTE: The Mute LED is illuminated when the system Soft Mute is active. Soft Mute
only affects output jack 2 (The second jack); jack 1 is not muted. This enables the non-
muted output to still drive a signal chain or be used for tuning.



AB: The AB LED is illuminated when the AB switch is active.



RCV: The Receive LED illuminates when the system is receiving commands from a
remote.



1, 2, 3, 4, TS1, TS2: These LED’s are illuminated whenever these loops or functions are
active.

Main Unit Rear Panel



GND:ISO (Isolated) This switch isolates audio ground from common chassis ground.
Useful when troubleshooting system ground issues or performing where grounding is
causing loud hum or noise. COM connects audio ground to common chassis ground.



AB: This switch selects Normally Open (NO) or Normally Closed (NC) Tip to Sleeve
orientation of the AB jack. Most amps use a NO style connection; meaning that when
the Tip and Sleeve are connected together it activates the channel switch in an amp. The
AB can be used to switch practically any switching need. The AB LED illuminates on the
front panel when the internal AB switch is active. See Diagram AB. (Note: at times it
might be necessary to build a custom wire from the switch jack on your amp if it is a
non-standard connector or switch. Give us a call and we can help you with this)



TS1 and TS2: These are effectively the exact same types of switches as the AB. We
separated these out so that it would be easier for artists to dedicate their TAP or TEMPO
style effects to these channels

and

to the TS buttons on the Floor Unit. However, these

can be used as basic switches just the same as the AB (See Diagram AB). When TS1
and/or TS2 are active their associated front panel LED’s will illuminate when the switch
is active.



OUTPUTS: Both output jacks are in parallel, but only the first one Mutes when mute is
selected. This allows the second output jack to be wired to a tuner, if desired.

«
...
2
3
4
5
6
...
»

Содержание STAGEPRO-8















Отзывы:

Нет отзывов