FXA FXAJF92109P, Инструкция по эксплуатации

Страница: 15 / 88

15
Always make a test cut on a piece of scrap wood
before cutting into the good material.
Use the slide action when cutting wide workpieces.
MAINTENANCE & CARE
CHANGING A BLADE
DANGER: The blade is extremely sharp and care must
be observed when handling. Never try to use a blade
larger than the stated capacity of the saw. It might
come into contact with the blade guards. Never use a
blade that is too thick to allow the outer blade washer
to engage with the flats on the spindle.
It will prevent the blade bolt from properly securing
the blade on the spindle.
Do not use the saw to cut metal or masonry.
Ensure that any spacers and spindle rings that may be
required suit the spindle and the blade fitted.
Make sure that the electrical plug is removed from the
power point.
Pull out the transportation lock and lift the saw arm to
its full height.
Rotate the lower blade guard (Fig.24) up and over the
upper blade guard. Rest the lower blade guard on the
screw on the inner plate, Fig.25. Press the spindle
lock button (Fig.26). Rotate the blade until the spindle
locks.
Use the 6mm Allen key to remove the blade bolt
(Fig.27). (Loosen in a clockwise direction as the blade
screw has a left hand thread).
Remove the washer, outer blade flange and the blade.
Wipe a drop of oil onto the inner blade washer and
the outer blade washer where they contact the blade.
Fit the new blade onto the spindle taking care that the
inner blade washer sits behind the blade.
CAUTION. To ensure correct blade rotation, always
install the blade with the blade teeth and the arrow
printed on the side of the blade pointing down
(Fig.28).
The direction of blade rotation is also stamped with an
arrow on the upper blade guard.
Replace the outer blade washer.
Depress the spindle lock button and replace the blade
bolt.
Use the 6mm Allen key wrench to tighten the blade
screw securely (anti-clockwise).
Check that the blade guard operates correctly and
covers the blade as the saw arm is lowered.
Connect the saw to the power supply and run the saw
to make certain that it is operating correctly.
Note: Check the tightness of the blade securing bolt
before, during and after each use.
MAINTENANCE
Keep the tool's air vents unclogged and clean at all
times.
Regularly check to see if any dust or foreign matter
has entered the grills near the motor and around the
trigger switch. Use a soft brush to remove any
accumulated dust. Wear safety glasses to protect
your eyes whilst cleaning.
Re-lubricate all moving parts at regular intervals.
If the body of the saw needs cleaning, wipe it with a
soft damp cloth. A mild detergent can be used but
nothing like alcohol, petrol or other cleaning agent.
Never use caustic agents to clean plastic parts.
CAUTION. Water must never come into contact with
the saw.
GENERAL INSPECTION
Check regularly that all fixation screws are sufficiently
tightened. Check especially the outer flange. If there is
vibration, screws can loosen with time.
Regularly check the device’s power cable and all
extension cables used for damage. If the supply cord
needs replacing, the task must be carried out by the
manufacturer, the manufacturer’s agent, or an
authorised service centre in order to avoid a safety
hazard. Replace damaged extension cables.
TECHNICAL SPECIFICATION
NOISE AND VIBRATION DATA
A weighted sound pressure: L
pA
99.6dB(A)
A weighted sound power: L
WA
112.6 dB(A)
Uncertainty K K=3dB(A)
Voltage 230 V~ 50 Hz
Rated input S1:1400W,
S6 25% 1700W
No load speed 5000 min -1
Saw Blade diameter Ø210mm
Teeth 48 HW
Saw Blade arbour Ø 30mm
Angle of mitre table -45°/0°/+45°
Bevel angles 45° to the left
Straight cut at 0° x 90° 120 x 60 mm
Mitre cut at 45° x 90° 80 x 60 mm
Bevel cut at 0° x 45° 120 x 30 mm
Combined Mitre cut at 80 x 30 mm
45° x 45°
Weight 8.8 kg