FXA FXAJ1G-ZP8-210C, Инструкция по эксплуатации

Страница: 11 / 92

11
Check the work piece for any protruding nails, screw
heads or anything that could damage the blade.
Do not attempt to modify the machine or its
accessories in any way.
Do not use excessive force when feeding the work
piece to the blade.
Feeding the work piece gradually will reduce wear on
the machine and blade increasing its efficiency and
operating life.
Do not use the saw without guards in position.
Replace table insert when worn.
Do not use the saw to cut material other than
aluminum, wood or similar materials.
Connect mitre saws to a dust collecting device when
sawing.
Select saw blades in relation to the material to be cut.
Take care when slotting.
WARNING! DO NOT ATTEMPT TO CUT MATERIAL
LARGER THAN THE MAXIMUM CUTTING CAPACITY.
ADDITIONAL SAFETY ADVICE CARRYING YOUR
MITRE SAW
Although compact, this Mitre Saw is heavy. To reduce
the risk of back injury, get competent help whenever
you have to lift the saw.
To reduce the risk of back injury, hold the tool close
to your body when lifting. Bending your knees so you
can lift with your legs, not your back. Lift by using the
handheld areas at each side of the machines base.
Never carry the Mitre Saw by the power cord.
Carrying the Mitre Saw by the power cord could
cause damage to the insulation or the wire
connections resulting in electric shock or fire.
Before moving the Mitre Saw tighten the mitre and
bevel locking screws and the sliding carriage locking
screw to guard against sudden unexpected
movement.
Lock the Cutting Head in its lowest position. Ensure
that the Cutting Head Locking Pin is completely
engaged in its socket.
WARNING: Do not use the blade guard as a ‘lifting
point’. The power cord must be removed from the
power supply before attempting to move the machine.
SAFETY RULES FOR LASER LIGHTS
The laser light/laser radiation used is Class 2 with
maximum 1mW power and 650nm wavelength.
These lasers do not normally present an optical
hazard, although staring at the beam may cause flash
blindness.
WARNING. Do not stare directly at the laser beam. A
hazard may exist if you deliberately stare into the
beam, please observe all safety rules as follows:
The laser shall be used and maintained in accordance
with the manufacturer’s instructions.
Never aim the beam at any person or an object other
than the workpiece.
The laser beam shall not be deliberately aimed at
personnel and shall be prevented from being directed
towards the eye of a person for longer than 0.25s.
Always ensure the laser beam is aimed at a sturdy
workpiece without reflective surfaces.l.e. wood or
rough coated surfaces are acceptable.
Bright shiny reflective sheet steel or the like is not
suitable for laser use as the reflective surface could
direct the beam back at the operator.
Do not change the laser light assembly with a different
type. Repairs must be carried out by the laser
manufacturer or an authorised agent.
GENERAL SAFETY RULES
WARNING!
Read all instructions Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious injury. The term "power tool" in all
of the warnings listed below refers to your mains
operated (corded) power tool or battery operated
(cordless) power tool.
SAVE THESE INSTRUCTIONS
1) WORK AREA
a) Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.