FXA FXAEP2800I, Инструкция по эксплуатации

Страница: 13 / 120

13
Hold down the generator firmly with one hand on the
frame. With the other hand grip the recoil starter cord
handle (Fig.11) and pull and return the rope gently 3-4
times to let the engine breath in the fuel mixture from
the carburetor. Pull the cord sharply. Continue this
procedure until the engine starts.
CAUTION. Avoid damaging the plastic case of the
crankshaft while pulling the rope. Aways return the
recoil starter cord handle slowly.
When the engine has been successfully started and is
running smoothly set the choke lever to the OPEN
position (Fig.12).
WARNING. Before connecting any electrical load to
the generator ensure that the load does not exceed
the maximum load as stated on the rating plate.
Ensure that the mains supply lead is long enough to
reach the generator without any strain.
When the generator engine has been successfully
started and is running smoothly connect the electrical
load to the generators AC output sockets.
STOPPING THE GENERATOR
WARNING.
In case of emergency, the easiest way to
stop the generator is to directly put engine switch to
OFF (O) position. Avoid doing so in non-emergency
circumstances as it carries the risk of damaging the
generator.
Before stopping the engine make sure that all the
electrical loads are disconnected from the generator
AC outlet socket.
Switch off the engine by putting the engine switch in
the OFF (O) position (Fig.13).
When the generator engine has stopped and before
storage, turn the fuel valve lever to the OFF position
(Fig.14).
NOTE. After disconnecting all loads, leave the
generator running for another 1-2 minutes before
shutting it down. Then switch off the engine switch
and the fuel valve. Switching off the engine with loads
attached may damage the unit and cause difficulty
starting the generator next time it is used.
MAINTENANCE
GENERAL MAINTENANCE
Keep the generator in a clean and dry environment
where it is not exposed to dust, dirt, moisture, or
corrosive vapours.
Do not allow the cooling air slots in the generator to
become clogged with foreign material such as leaves,
snow, etc.
Do not use a garden hose to clean the generator.
Water entering the fuel system or other internal parts
of the unit can cause problems that will
decrease the life of the generator.
To clean the unit:
Use a soft bristle brush and/or vacuum cleaner to
loosen and remove dirt and debris.
Clean air vents with low pressure air that does not
exceed 25 psi.
Wipe the exterior surfaces of the generator with a
damp cloth.
ENGINE OIL REPLACEMENT
Initial oil change: After the first 20 hours of operation.
Thereafter: Every 50 hours of operation.
Remove the oil filler cap/dipstick.
Place a container underneath the oil drainage plug to
collect used oil as it drains.
Unscrew the oil drainage plug and remove.
Allow oil to drain completely.
Reinstall the oil drainage plug and tighten securely.
Refill with oil following the instructions in the
Checking/Adding Oil section.
Reinstall the oil filler cap/dipstick.
Used oil should be disposed of at an approved
disposal site. See your local oil retailer for more
information.
CHECKING/CLEANING THE AIR FILTER
For proper performance and long life, keep air filters
clean.
Using a screwdriver unscrew the two air filter
connection screws located at the top and bottom of
the air filter cover. Remove the cover and set aside
(Fig.15).
Remove the filter elements (Fig.16).
If the filter elements are dirty, clean with warm, soapy
water. Rinse and let dry.
Apply a light coat of engine oil to the elements, then
squeeze it out.
Replace the elements in the air filter unit.
Replace the air filter cover and tighten the two air filter
connection screws.
NOTE : Do not run the generator without the air
filter. Rapid engine wear will result.
SPARK PLUG MAINTENANCE
The spark plug must be properly gapped and free of
deposits in order to ensure proper engine operation.
To check:
Remove the spark plug cap (Fig.17).
Clean any dirt from around base of spark plug.