background image

Test the board - NPN version

UNDER NO CIRCUMSTANCES will troubleshooting help

be offered if you have skipped this stage. No exceptions.

Once you’ve finished the circuit it makes sense to test is before starting on the switch and LED

wiring. It’ll cut down troubleshooting time in the long run. If the circuit works at this stage, but it

doesn’t once you wire up the switch - guess what? You’ve probably made a mistake with the switch.
Solder some nice, long lengths of wire to the board connections for -V, GND, IN and OUT. Connect

IN and OUT to the jacks as shown. Connect all the GNDs together (twist them up and add a small

amount of solder to tack it). Connect the b lead to the -V wire, same method. Plug in. Go!
If you’re using a ribbon cable you can tack the wires to the ends of that. It’s a lot easier to take them

off there than it is do desolder wires from the PCB pads. Check the daughterboard doc for details.
If it works, carry on and do your switch wiring. If not... aw man. At least you know the problem is

with the circuit. Find out why, get it working, THEN worry about the switch etc.

Your completed circuit board

including pots

Содержание Tone Bender Mk II










Отзывы: