What is S.BUS?
Different from conventional radio control systems the
S.BUS
system uses data communication to transmit control signals
from a receiver to a servo, gyro, or other
S.BUS
compatible
device. This data includes commands such as “move the
channel 3 servo to 15 degrees, move the channel 5 servo to
30 degrees” to multiple devices. The
S.BUS
devices execute
only those commands for their own set channel. For this
reason, it can be used by connecting multiple servos to the
same signal line.
[Connection by S.BUS system]
S.BUS hub
S.BUS hub
S.BUS output
S.BUS
Ch output/
Battery terminal
R6203SBE
Battery
S.BUS servo
Conventional
servo
2ch
4ch
3ch
5ch
6ch
* Set the channel at the
S.BUS
SERVOSBYUSINGAN
SBC-1
channel changer or a
CIU-2
53"SERIALINTERFACE
*
.&&%+<#+4!6A&%+!A+HA!@6A&%+!A+6&<#+4<9
S.BUS
#5#
*
#++!A+&!<&!95&6I@#+
S.BUS
H#<.&<%?&9G!<&!95&6I#+
%&+!:!+!#6&#&%:
S.BUS
H#<.&<%?&9G!<&!95&6I#+:!664
Operation Mode Select
The operation mode is on "Normal mode" from factory
shipping. When to change the mode, please follow the steps
shown below.
1
4URNOFFTHERECEIVER
2
0RESS AND HOLD THE
Link/Mode
SWITCH AND TURN ON
THEREEPTHESWITCHHOLDMORETHANONE
second. The
LED
STARTS FLASHING WITH THE CURRENT
STATUS
3
2ELEASETHESWITCH
4
4URNOFFTHERECEIVER
By doing this step, the mode can switch over between two(2)
modes.
0 to 1 sec.
More than 1 sec.
0 sec.
1 sec.
Press and Hold
Turn on the receiver.
No function
Showing the CURRENT
mode with blink.
Red Blink
= Normal
Green/Red Blink
=
High Speed
Solid as the mode changed.
Red Solid
= Normal
Green/Red Solid
= High
Speed
(Become
Red
after one (1)
second)
㸦
Function
㸧
To change the mode between
Normal and High Speed
㸦
LED Status
㸧
Please check the operation mode by observing the
LED
when
turning on the receiver. If possible there's no
FASST
transmitter
When turn on the receiver, the
LED
will be;
s2EDWHENON.ORMALMODE
s'REENAND2EDMAKES/RANGE WHENON(IGH3PEEDMODE
!FTERTWO SECONDSCHANGETO2ED
If there are some
FASST
transmitter turned on around the
receiver, the
LED
may show the above status for a brief
moment then changed to the status indication as shown in the
"
LED
indication" table.

WARNING
$O NOT PERFORM THE LINKING PROCEDURE WITH
MOTORgSMAINWIREISCONNECTEDASITMAYRESULT
INSERIOUSINJURY
7HILETHELINKINGISDONEPLEASECYCLERECEIVER
POWER AND CHECK IF THE RECEIVER TO BE LINKED IS
REALLYUNDERTHECONTROLBYTHETRANSMITTERTOBELINKED
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
JKL;N*N.OCOCN;POQ @
LED Indication
'REEN
2ED
3TATUS
Solid
Solid
)NITIALIZINGWHENON(IGH3PEEDMODE
Off
Solid
No signal reception
Solid
Off
2ECEIVINGSIGNALS
Blink
Off
2ECEIVINGSIGNALSBUT)$ISUNMATCHED
Alternate blink
5NRECOVERABLEERROR%%02/-ETC
Link to the transmitter
1
0RESS AND HOLD THE
Link/Mode
switch more than
TWO SECONDS
Re-adjust the F/S position (only for TM-8)
1
0RESSANDHOLDTHE
Link/Mode
SWITCHBETWEENONE
ANDTWO SECONDS
0 to 1 sec.
1 to 2 sec.
More than 2 sec.
0 sec.
1 sec.
2 sec.
Press and Hold
No function
With
TM-8
(not included in this set)
To set the F/S
position(No re-link)
Re-link(ID set) and to
set the F/S position
No function
Other than
TM-8
(not included in this set)
Re-link(ID set)