Link Procedure
Each transmitter has an individually assigned, unique ID code. In order to start
operation, the receiver must be linked with the ID code of the transmitter with
which it is being paired. Once the link is made, the ID code is stored in the
receiver and no further linking is necessary unless the receiver is to be used with
another transmitter.
1
Place the transmitter and the receiver close to each other within
half (0.5) meter.
2
Place the transmitter into the linking mode, and turn on the
receiver.
3
During countdown, push the receiver tact switch for
approximately 2 seconds. The LED will begin to blink red. After
the receiver LED switches from blinking red to green
→
green
(red) steady light, If the transmitter and receiver are linked
normally, set the power switch to the OFF position and then
return it to the PWR ON position. If the receiver LED lights
green, linking was successful. (T4PLS,T4GRS : set the power
switch to the OFF position and then return it to the PWR ON
position.) Actually check servo operation.
* Please refer to the table below for LED status and receiver condition.
* Refer to the transmitters operation manual for complete details on how to place the transmitter
into the linking mode.
* If there are many T-FHSS systems turned on in close proximity, your receiver might have
difficulty establishing a link to your transmitter. This is a rare occurrence. However, should
another T-FHSS transmitter/receiver be linking at the same time, your receiver could link to the
wrong transmitter. This is very dangerous if you do not notice this situation. In order to avoid
the problem,we strongly recommend you to double check whether your receiver is really under
control by your transmitter.
WARNING
After the linking is done, please cycle receiver power and check if the
receiver to be linked is really under the control by the transmitter to be linked.
Do not perform the linking procedure with motor's main wire connected
or with the engine operating as it may result in serious injury.
Operating Precautions:
Once the
R324SBS
detects the
T-FHSS
normal
mode
or
T-FHSS high speed mode
, the detected
mode is locked as long as the power is ON.
When need to change the mode, please
cycle power.
Note:
The R324SBS is compatible with the T-FHSS system transmitters.
The receiver type setting of the transmitter is set in T-FHSS.
*Futaba T-FHSS system does not work with current Futaba S-FHSS/FHSS/FASSTest/FASST /T-FHSS Air system.
Usage condition on "High Speed mode"
CAUTION
When using the high-speed mode, use a Futaba digital servo
(including brushless servo). Analog servos cannot be used.
• The use of analog servos may cause servo trouble.
1M23N17492
T-FHSS-2.4GHz System
Diversity antenna
S.BUS2, 4-Channel Receiver for Model Car
Thank you for purchasing the
R324SBS
receiver. The
R324SBS
is designed for use
with the Futaba
T-FHSS
system transmitter.
The
R324SBS
receiver has adopted the newly
developed bidirectional communication
system "
T-FHSS
".
• Telemetry system
With the
telemetry system
, the running status can be displayed at the transmitter. The telemetry data can be checked at the
transmitter by connecting the
telemetry sensor
sold separately to the
S.BUS2
connector of the
R324SBS
receiver.
• Normal mode/High Speed mode
The "Normal mode" accepts any type of servos or the peripheral. The "High Speed mode" only accepts the digital servos,
including BLS series, and most peripheral equipments such as the brushless ESCs. Please pay special attention to the information
contained within this manual and transmitter's manual in order to have a pleasant running experience.
• Diversity antenna equipment
R324SBS
WARNING
NEVER
use dry batteries for the power supply of the
R324SBS
as
this may cause difficulties with the receiver's operation.
Wrap the receiver with something soft,
such as foam rubber, to avoid
vibration. Do not splash water over the receiver.
Since the receiver generates a certain amount of heat, install the
place with good ventilation.
Do not put any conductive equipment/sticker on the antenna part.
(Receiver top)
• Otherwise, the operating range may become shorter.
No signal reception
LED: Red
Receiving signals
LED: Green
Unrecoverable fail-
ure (EEPROM,etc.)
LED: Red and
Green turn on
alternately
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
©FUTABA CORPORATION 2017, 2 (1)
R324SBS Specifications:
(
T-FHSS
system,
S.BUS2
, 4-channel receiver)
• Receiving on 2.4GHz band
• System:
T-FHSS
system
At Normal/High speed mode (auto detection)
• Power requirement Operating voltage: 3.7V-7.4V
• F/S and Battery F/S function:It is set according to the transmitter used.
• Battery F/S voltage: Set it with the transmitter arbitrarily.
• Size: 1.38x0.91x0.49” (35.1x23.2x12.5mm)
• Weight: 0.29oz. (8.3g)
HUB
Battery
Steering servo
Throttle servo
Collect many
telemetry
sensors
by
HUB
and connect
them to
S.BUS2
port.
(It connects with port which is not used.）
*When all the ports are used, connect
a battery using HUB or Y-harness.
Built-in antenna
*Receiver top is clean.
Out side Antenna
Link Switch
CH4
CH1
S.BUS2
CH2
LED
Temperature
sensor
RPM sensor
Voltage sensor
Telemetry sensors
(Option)
*Don't cut or bundle
the receiver
antenna wire.
The Example of Connection
LED Indication
Compliance Information Statement (for U.S.A.)
This device, trade name Futaba Corporation, model number R324SBS, complies with part15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
CAUTION:
To assure continued FCC compliance:
1. Any changes or modifications not expressly approved by the grantee of this device could void the user's authority
to operate the equipment.
2. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: [email protected] (Support)