19
18
9 -
Operation mode (
green
+
blue
+
red
blinking twice)
11 -
Full boost timing (green blinking 4 times)
TUNING THE DRIVING EXPERIENCE
In the select mode (the
gre
e
en
n
+
blue
+
red
LEDs blinking twice), press the
SET button for 2 seconds or more to
enter the setting mode. Each time the
SET button is pressed once, the LED
patter n changes and the operating
mode changes as shown on the right.
Align the LED with your favorite setting,
and press the SET button for 2 seconds
or more. The set value is validated and
it returns to select mode. The changed
value will be reset if the power is turned
off without saving. Please save your
settings before turning your unit off (Page
22).
With crawler-oriented settings, the brake will not work and the ESC will switch
between forward and reverse instantly. This function must not be used on
non-crawler vehicles otherwise damage to the ESC, motor, or gears may occur.
In general,"boost + turbo" function will overload the ESC/motor. Pay close
attention to the heating of the ESC / motor as well as the gear ratio when
using these functions.
WARNING
When using "boost +t urbo" or "boost" only, please use a motor of 8.5T turn
(with FAN ) or higher. Damage caused by using a motor with a lower turn
count will not be covered by warranty.
In the select mode (the
blue
+
red
+
orange
LEDs
blinking twice), press the SET button for 2 seconds or
more to enter the setting mode. Each time the SET
button is pressed once, the LED pattern changes and
the cutoff voltage value changes as shown on the
right. Align the LED with your favorite setting, and
press the SET button for 2 seconds or more. The
set value is validated and it returns to select mode.
The changed value will be reset if the power is turned
off without saving. Please save your settings before
turning your unit off (Page 22).
Because the number of cell is automatically recognized, select the voltage per
cell. If set to disabled, pay close attention to your runtime.
Reference
About Boost / Turbo Function
What is the boost function?
What is the turbo function?
It is a function that increases the electronic timing in
conjunction with the motor rpm to further increase motor rpm.
It is a function that increases the electronic timing when in full
throttle to increase motor rpm.
If "boost / turbo disabled" has been selected in Load program, the "boost function" and
"turbo function" cannot be used.
When using the "boost/turbo disabled" program, zero timing will be activated, and
while in standby, the blue LED will blink in "ESC mode" and the
red
LED will blink
in "program card mode". This is also known as a "Blink mode". It allows the user
understands at a quick glance that the ESC is in zero timing modes and that "boost/
turbo" is disabled.
The "MC970CR" ESC allows to operating either "boost function" or "turbo function"
independently. (When doing so, make sure to use a program other than "boost/turbo
disabled".)
In the select mode with (the
green
LED blinking 4
times), press the SET button for 2 seconds or more to
enter the setting mode. Each time the SET button is
pressed once, the LED pattern changes and the boost
timing value changes as shown on the right. Align the
LED with your favorite setting, and press the SET button
for 2 seconds or more. The set value is validated and it
returns to select mode. The changed value will be reset
if the power is turned off without saving. Please save
your settings before turning your unit off (Page 22).
Switched between normal and reverse motor rotation. Regardless of whether
the initial settings have been completed properly, the car may go into reverse
once the throttle is applied. If this condition occurs, please use Reverse rotation
operation mode. The orange LED will be lit in standby mode when Reverse
rotation is selected.
Commentary
CAUTION
It is a function to notify the driver of low voltage condition before the unit reaches
critical voltage and performance decrease. When the voltage reaches the cutoff
voltage while driving, the green LED will fl ash and the vehicle will travel very
slowly. When disabled is selected, this function will not work. Please be careful
about your runtime and other conditions.
This determines the maximum value (terminal value) for timing increased
through boost.
Commentary
Commentary
A d v i c e
CAUTION
Forward rotation
Reverse rotation
Forward rotation
Reverse rotation
Forward rotation
Reverse rotation
F Brake
F Brake
F Brake + Reverse
F Brake + Reverse
F Brake (for crawlers)
F Brake (for crawlers)
Disabled
3.0V/Cell
2.8V/Cell
3.1V/Cell
3.2V/Cell
3.4V/Cell
10 -
Cutoff voltage (
blue
+
red
+ orange blinking twice)
0 deg
25 deg
15 deg
45 deg
Содержание MC970CR
Страница 1: ...Produced by INSTRUCTION MANUAL ...
