manualshive.com logo in svg

FUTABA GY701, Руководство по установке

Поделиться
Скачать
FUTABA GY701 Скачать руководство пользователя страница 68

G

YRO 

E

XPERT 

S

ETTING

68

(10) Pirouette speed

default:

 

450 deg/sec (F3C), 720 deg/sec (3D)

ranges:

 

100

〜

999 deg/sec

This adjusts the pirouette speed of the rudder. 
The default values are set 450 deg/sec on F3C 
mode and 720 deg/sec on 3D mode when rudder 
is 100 %. The bottom of the line shows the actual 
pirouette speed of the rudder. When this value 
exceeds 1200 deg/sec, the gyro is out of control, 
the pirouette speed is very quick and this can be a 
dangerous situation. Pushing the data+ or – key, 
the value is changed.

(11) Gain change up delay

default: 12
ranges: 1

〜

50

This sets the delay of the gyro gain from low to 
high, the value represents from idle up to hover-
ing. Increasing this value may stop tail hunting 
if it is taking place. Pushing data+ or – key, the 
value is changed.

(12) Gain change down delay

default: 3
ranges: 1

〜

50

This sets the delay of the gyro gain from high to 
low, the value represents from hovering to idle up. 

Содержание GY701
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды