manualshive.com logo in svg

FUTABA GY601, Инструкция по эксплуатации

Поделиться
Скачать
FUTABA GY601 Скачать руководство пользователя страница 33

33

I

NSTALLATION

 

AND

 A

DJUSTMENT

2

 Connections

Connect the GY601, receiver
and servo as shown below.

Insert the connectors
fully and firmly.
If a connector works loose
due to vibration during
flight, control may be lost
and result in a dangerous
situation.

•Connect the sensor to the

amp sensor input ("GYRO").

•Connect the rudder servo to

the amp servo output ("SX").

•Connect the amp rudder

input ("RX,1-4") input
connector to the receiver
rudder channel (ch4).

Black

Red

•Connect the amp remote

gain input ("RX,AUX")
connector to the receiver
sensitivity setting channel
(normally ch5).

To receiver

When using the gyro only in the NOR mode,
select NOR. When using the gyro only in the
AVCS mode. select AVCS. When using the
gyro in both the AVCS and NOR modes,
select CMT.

3

 Gyro operation mode selection

(S9251 only)

Always use the special S9251 servo with the GY601.

The GY601 cannot operate with servos other than the S9251.
The servo may be destroyed.

Содержание GY601












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды