Furuno LH-3000 Скачать руководство пользователя страница 41

FURUNO Warranty for North America 

 

FURUNO U.S.A., Limited Warranty provides a twenty-four (24) months LABOR and twenty-four (24) months PARTS 
warranty on products from the date of installation or purchase by the original owner. Products or components that are 
represented as being waterproof are guaranteed to be waterproof only for, and within the limits, of the warranty 
period stated above. The warranty start date may not exceed eighteen (18) months from the original date of purchase 
by dealer from Furuno USA and applies to new equipment installed and operated in accordance with Furuno USA’s 
published instructions. 
 
Magnetrons and Microwave devices will be warranted for a period of 12 months from date of original equipment 
installation. 
 
Furuno U.S.A., Inc. warrants each new product to be of sound material and workmanship and through its authorized 
dealer will exchange any parts proven to be defective in material or workmanship under normal use at no charge for a 
period of 24 months from the date of installation or purchase. 
 
Furuno U.S.A., Inc., through an authorized Furuno dealer will provide labor at no cost to replace defective parts, 
exclusive of routine maintenance or normal adjustments, for a period of 24 months from installation date provided the 
work is done by Furuno U.S.A., Inc. or an AUTHORIZED Furuno dealer during normal shop hours and within a radius 
of 50 miles of the shop location. 
 
A suitable proof of purchase showing date of purchase, or installation certification must be available to Furuno U.S.A., 
Inc., or its authorized dealer at the time of request for warranty service. 
 
This warranty is valid for installation of products manufactured by Furuno Electric Co. (hereafter FURUNO). Any 
purchases from brick and mortar or web-based resellers that are imported into other countries by anyone other than a 
FURUNO certified dealer, agent or subsidiary may not comply with local standards. FURUNO strongly recommends 
against importing these products from international websites or other resellers, as the imported product may not work 
correctly and may interfere with other electronic devices. The imported product may also be in breach of the local 
laws and mandated technical requirements. Products imported into other countries, as described previously, shall not 
be eligible for local warranty service. 
 
For products purchased outside of your country please contact the national distributor of Furuno products in the 
country where purchased. 

 

WARRANTY REGISTRATION AND INFORMATION 

To register your product for warranty, as well as see the complete warranty guidelines and limitations, please visit 

www.furunousa.com

 and click on “Support”. In order to expedite repairs, warranty service on Furuno equipment is 

provided through its authorized dealer network. If this is not possible or practical, please contact Furuno U.S.A., Inc. 
to arrange warranty service. 

FURUNO U.S.A., INC. 

Attention: Service Coordinator 

4400 N.W. Pacific Rim Boulevard 

Camas, WA 98607-9408 

Telephone: (360) 834-9300 

FAX: (360) 834-9400 

 

 
Furuno U.S.A., Inc. is proud to supply you with the highest quality in Marine Electronics. We know you had several 
choices when making your selection of equipment, and from everyone at Furuno we thank you. Furuno takes great 
pride in customer service.

 

Содержание LH-3000













































Отзывы: