6. SIGNALLING
Led THERM on -
Led HUMID on -
Led AUX on -
Led BUZZ on -
T
H
Auxiliar
- Irregular temperature sensor
- Irregular humidity sensor
-
hermostat output on
umidistat output on
output on
Invalid configuration parameters;
- In this situation the outputs are turned off;
- Check which parameters have invalid data and correct them to return to normal operation.
Buzzer activated
7. SELECTION OF THE UNIT (Cº / Fº)
In order to define the unit that the instrument will operate in, enter function “F01” with the access code
“231” and confirm with the
key. Press the
key and the indication
will appear. Press
to choose between
or
and confirm. After selecting the unit the
message will
appear, and the instrument will return to the function “F01”. Every time that the unit is changed, the
parameters should be reconfigured, since they assume the “standard” values.
SET
SET
8. WIRING DIAGRAM
2 3 4 5 6 7 8
10 11 12
COMMON
THERM
(NO)
HUMID
(NO)
Above specified current
use contactors.
Power supply
and relays
common
0
1
Loads
supply
AUX
(NO)
115V
(12V )
230V
(24V )
Loads
L3
L2
L1
- Dehumidificator
- Humidificator
- Contactor
- Solenoid
- Alarm
L3
- Dehumidificator
- Humidificator
- Contactor
- Solenoid
L2
- Contactor
- Solenoid
L1
9
Yellow
Green
Orangr
and
Brown
Red
Serial
communication
RS-485
A
B
Temperature and
humidity sensor
Cable: SB56
Violet protector
To
the
terminal
of
the
distribution
box
9 - 8
9 - 7
115V
230V
MT-530 Super
12V
24V
MT-530L Super
IMPORTANT
1:
2:
3:
According to the chapters from the IEC60364 standard:
Install
on power supply
Sensor cables and computer signals can be together, however not at the same place where power
supply and load wires pass for
Install suppresor of transient in parallel to loads to increase the usefull life of the relays
protectors against over voltage
Wiring diagram of suppresors in contactors
Suppresor
A1
A2
A1 e A2 are the
contactor coils.
Wiring diagram of suppresor for direct drive
Load
Suppresor
For direct activation the maximum
specified current should be taken
into consideration.
Note:
The sensor cable lenght can be increased by the user until 200 meters using 4 x 0,20mm² cable.
A B
RS-485 Network
RS-485 Serial Interface
®
Device used to establish the
connection Full Gauge Controls’
instruments with the Sitrad
.
Instrument
RS-485 Network
External
mesh
®
Integrating Controllers, RS-485 Serial Interface and Computer
A
B
A
A
B
B
A B
A
A
B
B
A B
A
A
B
B
A B
A
B
A
B
A
A
B
B
A B
Serial interface
RS-485
Full Gauge
MOD 64
A
A
B
B
A B
terminal
grounded
Distribution Box
Used to connect more than one instrument to the Interface. The wire's connections must
be made in agreement with the following rules: terminal
of the instrument connects to
the terminal
of the distribution box, that must be connected with the terminal
of the
Interface. Repeat the action for terminals and
, being
the cable shield.
A
A
A
B
The terminal
of distribution box must be connected to the respective terminals
of
each instrument.
OUT
1
OUT 2
OUT 3
P
C
T-4
0
0
R
p
lu
s
OUT 4
ALMR
PUMP
AUX
1
AUX 2
M
IC
R
O
S
O
L
II
plu
s
ENVIRONMENTAL INFORMATION
Package:
Products:
Disposal:
The packages material are 100% recyclable. Just dispose it through specialized
recyclers.
The electro components of Full Gauge controllers can be recycled or reused if it is
disassembled for specialized companies.
Do not burn or throw in domestic garbage the controllers which have reached the end-of-
life. Observe the respectively law in your region concerning the environmental
responsible manner of dispose its devices. In case of any doubts, contact Full Gauge
controls for assistance.
PROTECTIVE
:
VINYL
This adhesive vinyl (included inside the packing) protects the instruments against
water drippings, as in commercial refrigerators, for example. Do the application after
finishing the electrical connections.
Remove the protective paper
and apply the vinyl on the entire
superior part of the device,
folding the flaps as indicated by
the arrows.
72 mm
Dimension of the clipping
for setting of the instrument
in panel
29
mm
