Fukuda FRE-203XT Скачать руководство пользователя страница 11

Страница: 11 / 33

CHARGING & BATTERIES

The FRE-203XT is supplied with a Fukuda 4.8V Ni-MH Rechargeable Battery, a Fukuda 6V

Alkaline Battery (Non-rechargeable) and a 5.6 Volt UK Plug, 900mA charger. Typically only the

rechargeable battery pack is used, with the alkaline battery pack being used as a back-up power

source.

Rechargeable Battery Pack

The 5.6 Volt UK Plug, 900mA charger (Input 100-240V AC 50/60Hz. Output DC 5.6V 900mA,

centre pin + polarity) is for indoor use only. If the charger becomes damaged, stop using

immediately and purchase a replacement.

Never use a generic charger with this laser.

●

Prior to ﬁ rst use, we recommend that you fully charge the battery pack for around 7-8 hours.

●

The battery pack contains 4 x “sealed for life” Ni-MH type C, 4000mAh, 1.2V cells. Please note

that this battery pack can be charged either in or outside of the laser.

●

Important:

NOT

allow battery to go completely ﬂ at before recharging.

Mains Charger

●

The general procedure to adopt is use the laser during the day & charge-up overnight. You

cannot damage the system by “over-charging” the batteries.

●

When the charger is plugged into a 230V mains supply (but not connected to the Laser), the

red LED on the charger will ﬂ ash once per second, when operating correctly.

●

Plug the charger into the charging port located on the battery pack or underneath the control

panel on the front face of the laser. Both allow the battery to charge.

●

When charging, the red LED on the charger will stop ﬂ ashing and be illuminated

continuously.

●

The LED will change to green when there is suﬃ cient charge in the battery.

●

The FRE-203XT can be operated with the charger connected to the mains supply, if required

and is approved on site.

●

The Mains Charger will charge most batteries in around 7 hours to give approximately 20

hours of continuous use. It takes 4 to 5 charge/discharge cycles for these battery packs to

reach their maximum capacity.

Alkaline Battery Pack (Non-rechargeable)

●

The Alkaline Battery Pack is designed to be a backup power source if the main rechargeable

battery has not been charged.

●

The battery pack contains 4 x type C, 1.5V alkaline batteries. These are readily available from

all good hardware stores / supermarkets.

●

Important:

NOT

attempt to recharge this battery, otherwise serious damage will occur.

Содержание FRE-203XT


































Результаты поиска

Содержание FRE-203XT

Отзывы:

Похожие инструкции для FRE-203XT

Бренды по названию

Популярные бренды

Fukuda FRE-203XT, Руководство пользователя

Результаты поиска

Содержание FRE-203XT

Отзывы:

Похожие инструкции для FRE-203XT

Бренды по названию

Популярные бренды