Fujitsu SPARC Enterprise T2000 Скачать руководство пользователя страница 72

Страница: 72 / 88

SPARC Enterprise T2000 Server Installation Guide • April 2007

To understand the various devices and their path names as represented in the
OpenBoot device tree, refer to

. The table identifies each of the devices, their

full path name and their location or NAC name used to identify their physical
location.

Booting the Solaris Operating System

The Solaris OS is preinstalled on SPARC Enterprise T2000 server on the disk in slot
0. The Solaris OS is not configured (that is, the

sys-unconfig

command was run in

the factory). If you boot the system from this disk, you will be prompted to configure
the Solaris OS for your environment.

▼

To Boot the Solaris Operating System

1. At the

prompt, boot from the disk that contains the Solaris OS.

If you know which disk to boot from, skip

Step a

and perform

Step 2

TABLE 3-1

Map of Devices, OpenBoot Path Names, and Locations

OpenBoot Device Path Name

Device

Location Name

/pci@780

Fire IO Bridge Bus A

IOBD/PCIEa

/pci@780/pci@0

PLX 8532 PCI-E Switch A (U0901)

IOBD/PCI-SWITCH0

/pci@780/pci@0/pci@1

Intel Ophir GBE Chip (U2401)

IOBD/GBE0

/pci@780/pci@0/pci@8

PCI-E Slot 0 (J2100)

PCIE0

/pci@780/pci@0/pci@9

LSI 1064-E SAS Controller (U3401)

IOBD/SASHBA

/pci@7c0

Fire IO Bridge Bus B

IOBD/PCIEb

/pci@7c0/pci@0

PLX 8532 PCI-E Switch B (U1501)

IOBD/PCI-SWITCH1

/pci@7c0/pci@0/pci@2

Intel Ophir GBE Chip (U2601)

IOBD/GBE1

/pci@7c0/pci@0/pci@1

Intel 41210 Bridge Chip (U2901)

IOBD/PCI-BRIDGE

/pci@7c0/pci@0/pci@1/pci@0,2

PCI-X Slot 0 (J3301)

PCIX0 (J3301)

/pci@7c0/pci@0/pci@1/pci@0,2

PCI-X Slot 1 (J3201)

PCIX1 (J3201)

/pci@7c0/pci@0/pci@1/pci@0

ULI Southbridge Chip (U3702)

IOBD/PCIX-IO

/pci@7c0/pci@0/pci@8

PCI-E Slot 1 (J2202)

PCIE1 (J2202)

/pci@7c0/pci@0/pci@9

PCI-E Slot 2 (J2201)

PCIE1 (J2201)

Содержание SPARC Enterprise T2000

























































































Результаты поиска

Содержание SPARC Enterprise T2000

Отзывы:

Fujitsu SPARC Enterprise T2000, Руководство по установке, Страница: 72 / 88

Результаты поиска

Содержание SPARC Enterprise T2000

Отзывы: