Fujitsu SP-1120N Скачать руководство пользователя страница 112

Страница: 112 / 147

Paper Jams/Pick Errors Occur Frequently

Check the following points

●

Do the documents meet the paper requirements? (page 112)

●

Is there any foreign matter in the ADF? (page 112)

●

Is there a document remaining in the ADF? (page 112)

●

Is the roller set (the brake roller and pick roller) installed correctly? (page 112)

●

Is the roller set (the brake roller and pick roller) clean? (page 112)

●

Is the roller set (the brake roller and pick roller) worn out? (page 113)

If the problem still persists, check each item in

Before You Contact the Scanner Service Provider (page

117)

first, then contact the distributor/dealer where you purchased this product. Refer to the contact

information in the Contact List if supplied with this product, or refer to the contact information in the
Contact for Inquiries section if provided in Safety Precautions supplied with this product, and then make an
inquiry.

●

Do the documents meet the paper requirements?

Solution

Use documents that meet the requirements.
For details, refer to

Documents for Scanning (page 52)

●

Is there any foreign matter in the ADF?

Solution

Clean the ADF.
Remove any foreign matter from the ADF.
For details, refer to

Daily Care (page 66)

●

Is there a document remaining in the ADF?

Solution

Remove the document from the ADF.
For details, refer to

When a Paper Jam Occurs (page 87)

●

Is the roller set (the brake roller and pick roller) installed correctly?

Solution

Install the roller set (the brake roller and pick roller) correctly.
For details, refer to

Replacing the Roller Set (page 79)

●

Is the roller set (the brake roller and pick roller) clean?

Solution

Clean the roller set (the brake roller and pick roller).

Troubleshooting

112

Содержание SP-1120N




















































































































































Результаты поиска

Содержание SP-1120N

Отзывы:

Похожие инструкции для SP-1120N

Бренды по названию

Популярные бренды

Fujitsu SP-1120N, Руководство оператора

Результаты поиска

Содержание SP-1120N

Отзывы:

Похожие инструкции для SP-1120N

Бренды по названию

Популярные бренды