Fujitsu PRIMERGY TX1320 M4 Скачать руководство пользователя страница 30

Страница: 30 / 102

Operating Manual

TX1320 M4

Product description

[CSS]

CSS
indicator

off

No critical event detected (CSS
component).

orange
on

Prefailure event detected (CSS
component).

For HDDs/SSDs, see also

"HDD/SSD prefailure detection" on
page 32

flashing
orange

CSS component failure detected.

Global
Error
indicator,
see also

off

No critical event detected (non CSS
component).

orange
on

Prefailure event detected (non CSS
component).

flashing
orange

Non CSS component failure
detected.
Possible causes:

– System is out of the specified

temperature range

– Defective sensor
– CPU error
– Error detected by server

management software

HDD/SSD
activity
indicator

flashing
green

Data access in progress.

Power-on
indicator

off

The server is switched off.

green on

– The server has been switched on

but Power Cycle Delay settings
delay it from turning on for a
specified time.

– The server is switched on and

operating normally.

flashing
green
slowly

The BMC firmware is starting up after
the server has been connected to the
mains.

Pos. Label

Indicator

Status

Description

Содержание PRIMERGY TX1320 M4







































































































Результаты поиска

Содержание PRIMERGY TX1320 M4

Отзывы:

Похожие инструкции для PRIMERGY TX1320 M4

Бренды по названию

Популярные бренды

Fujitsu PRIMERGY TX1320 M4, Руководство по эксплуатации

Результаты поиска

Содержание PRIMERGY TX1320 M4

Отзывы:

Похожие инструкции для PRIMERGY TX1320 M4

Бренды по названию

Популярные бренды