Fujitsu PRIMERGY RX2530 M1 Скачать руководство пользователя страница 82

Страница: 82 / 86

Operating Manual

RX2530 M1

Troubleshooting and tips

8.2

Server switches itself off

Server Management has detected an error

Check the error list of System Event Log in ServerView Operations Manager
or in the iRMC web interface, and attempt to eliminate the error.

8.3

Screen remains blank

Monitor is switched off

Switch on your monitor.

Screen has gone blank

Press any key on the keyboard.

Deactivate screen saver. Enter the appropriate password.

Brightness control is set to dark

Set the brightness control on the monitor to light. For detailed information,
refer to the operating manual supplied with your monitor.

Power cable or monitor cable not connected

Switch off the monitor and the server.

Check whether the power cable is properly connected to the monitor and to
the grounded power outlet.

Check whether the monitor cable is properly connected to the server and
monitor (if it is plugged in with a connector). If a separate graphics card is
installed in the server, then the monitor cable must be connected to the
graphics card.

Switch on the monitor and the server.

Содержание PRIMERGY RX2530 M1























































































Результаты поиска

Содержание PRIMERGY RX2530 M1

Отзывы:

Fujitsu PRIMERGY RX2530 M1, Руководство по эксплуатации, Страница: 82 / 86

Результаты поиска

Содержание PRIMERGY RX2530 M1

Отзывы: