Fujitsu PRIMERGY RX200 S7 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 86

Fujitsu PRIMERGY RX200 S7 Скачать руководство пользователя страница 54

54

Operating Manual

RX200 S7

Hardware installation

One optional video connector (1), one optional Front LAN connector (2) and two
additional USB connectors (3) are located on the front of the server (

figure 3

):

Figure 3: Connectors on the front

Connecting the keyboard, mouse and monitor

Ê

Connect the keyboard and mouse to the USB connectors of the server.

Ê

Connect the monitor to one of the two video connectors at the front or rear.

I

The front video connector is designed for maintenance issues. If you
connect a monitor to the video connector at the front, the video
connector at the rear is deactivated. A monitor connected to the front
must have at least the same resolution as the monitor connected to
the rear. A console bypass is not possible via the video connector at
the front.

I

If a separate graphics card is installed in a slot, the graphic controller
on the system board is automatically deactivated. The corresponding
video connector can not be used. Plug the video cable of the monitor
into the video connector of the graphics card.

Ê

Connect the power cord of the monitor to the mains socket strip of the rack.

I

The rated current for the monitor is indicated on the technical data label
on the monitor or in the operating manual for the monitor.

«
...
52
53
54
55
56
...
»

Содержание PRIMERGY RX200 S7























































































Отзывы:

Нет отзывов