Fujitsu PRIMERGY RX1330 M1 страница 17 Скачать руководство пользователя | Manualshive

Страница: 17 / 84

background image

RX1330 M1

Operating Manual

17

Functional overview

Hard disk drives

The server is shipped with one of the following drive cages:

– For up to four 3.5-inch SAS/SATA HDD modules:

Up to four 3.5-inch SAS/SATA HDD modules can be used in the drive cage.
Each HDD module can accommodate an SAS/SATA hard disk drive with a
maximum height of 1 inch. The module is connected to the SAS/SATA
backplane wirelessly. This allows HDD modules to be plugged in or pulled
out easily.

Hybrid configurations of SAS and SATA HDD modules within one drive cage
are not supported.

– For up to four, eight or ten 2.5-inch SAS/SATA HDD modules or 2.5-inch

SATA SSD modules:

Each module can accommodate SAS/SATA hard disk drive or an SATA SSD
drive with a 2.5-inch format. The HDD/SSD modules are connected to the
SAS/SATA backplane wirelessly. This allows modules to be plugged in or
pulled out easily.

I

Up to ten SAS/SATA drives are controlled by the SAS/SATA RAID
controller already installed.

I

Configurations with Eco SATA can only be mixed with BC SATA HDD
type. SAS and BC SATA drives with the same size can be mixed, but
not used in the same logical RAID volume.

Hybrid configurations of SATA HDD and SATA SSD modules are supported.

If the server has the corresponding RAID configuration, the HDD/SSD modules
can also be replaced during operation.

Onboard SATA controller

A SATA controller is integrated on the system board; up to four SATA hard disk
drives can be connected to the controller. The LSI Embedded MegaRAID
software (SATA Software RAID) supports RAID levels 0, 1 and 10.

For more information on configuring the controller, see section

"Configuring the

onboard SATA controller" on page 71

.

«
...
15
16
17
18
19
...
»

Содержание PRIMERGY RX1330 M1





















































































Отзывы:

Нет отзывов

Похожие инструкции для PRIMERGY RX1330 M1

BladeCenter HS23

Бренд: IBM Страницы: 36

301300U - Ethernet Disk NAS Server

Бренд: LaCie Страницы: 62

Бренд: LevelOne Страницы: 88

Бренд: Atop Страницы: 52

1-Port USB Print Server

Бренд: IBM Страницы: 15

Бренд: Emerson Страницы: 23

DIXELL XWEB5000 PRO

Бренд: Emerson Страницы: 20

Бренд: Emerson Страницы: 18

Avocent ACS 6000

Бренд: Emerson Страницы: 93

Бренд: Emerson Страницы: 114

Centellis 2000 Shelf Release 3.0

Бренд: Emerson Страницы: 194

Бренд: Emerson Страницы: 222

TeraStation TS-RXL/R5

Бренд: Buffalo Страницы: 91

Бренд: Wyse Страницы: 2

Бренд: Digital Watchdog Страницы: 7

Blackjack Tower DW-BJST51T Series

Бренд: Digital Watchdog Страницы: 14

G4-40G-010-384T

Бренд: Viavi Страницы: 12

Бренд: Super Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды