manualshive.com logo in svg

Fujitsu PRIMEQUEST 440, Руководство по проектированию систем

Поделиться
Скачать
Fujitsu PRIMEQUEST 440 Скачать руководство пользователя страница 197

C122-B001-02EN

6-19

 

6.5 Redundancy of the Business LAN (Use of PRIMECLUSTER GLS)

With this method, as shown in 

Figure 6.15

, duplicated NICs are connected on the 

same network, and switching of transmission lines is controlled by exclusive use 
(during normal operation, put one NIC in the "up" status for communication).  A 
TCP/IP application can communicate with a destination system without having to 
take into consideration switching of NICs, by using the IP address set in the physical 
interface in the "up" status as the own system IP address.

As the connection pattern, duplicated NICs should be connected on the same network.  
It is possible to connect to a communication destination system either on the same 
network or on a different network via a router.

If each of the network devices in a multi-vendor environment (hub, router, and other 
devices) has a duplication function, the reliability of the whole system can be 
improved by combining devices.  In this case, the range of duplication is defined 
separately for each vendor.

Figure 6.15  NIC switching method

Содержание PRIMEQUEST 440

























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды