Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 53

Страница: 53 / 344

Condition

Required setting

Connect the REMCS port to the external switching hub.

Alternatively, connect the center from the external switch of

the management port through the firewall.

- P-P connection:

Connect the REMCS port on each of MMB#0 and MMB#1

directly to the dial-up router.

For details on REMCS linkage, see the

PRIMEQUEST 1000

Series REMCS Installation Manual

(C122-E120EN).

Remarks

- The MMB sends NTP, Alarm E-Mail, REMCS, and SNMP Trap packets. If both physical and virtual IP

addresses are set for the MMB, the sender's IP address in the packets is the physical IP address of the MMB.

- PRIMECLUSTER linkage also uses the physical IP address of the MMB.

3.3.4

Logging in to the MMB

This section describes how to log in to the MMB.

Login to and logout from the MMB Web-UI

The login and logout procedures for the MMB Web-UI are described below.

Set one of the following for login to the Web-UI:

- Virtual IP address

- FQDN (fully qualified domain name) corresponding to the virtual IP address

Caution

- The MMB Web-UI supports the following browsers. Other browsers may incorrectly display the Web-UI

window. Be careful about the browser used.

- Microsoft Internet Explorer 6 (Service Pack 1) or later. FireFox 15 or later should be used for IPv6.

- Mozilla FireFox 3.0 or later. FireFox 15 or later should be used for IPv6.

- Do not attempt multiple logins (e.g., multiple logins with the same user name) from one MMB console PC

through the Web-UI to the PRIMEQUEST 1000 series system. Multiple logins may cause the following

problems, depending on the browser type or version. In a tabbed browser, avoid using multiple tabs for one

- The operating privileges of a logged-in user may change to those of a user who logs in later to the

Web-UI.

- One user logging out from the Web-UI may also log out all other users from the Web-UI.

Remarks

To specify an FQDN, you must configure a DNS server on the MMB console PC. For details on how to configure

a DNS server, see

3.3.8 Configuring a DNS server

Logging in

1. Start your Web browser.

Remarks

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 3 Work before Operating System Installation

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды