Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 62

Страница: 62 / 344

Operations

1. Click [Network Configuration] - [Network Protocols].

>> The [Network Protocols] window appears. For details on the [Network Protocols] window, see 1.5.4

[Network Protocols] window in the

PRIMEQUEST 1000 Series Tool Reference

(C122-E110EN).

FIGURE 3.10 [Network Protocols] window (example)

2. Specify each item in [Telnet].

Note

The MMB uses the following fixed TCP/IP port numbers. Do not change the following port numbers:

- 623/udp: Port for RMCP communication

- 664/udp: Port for RMCP communication

3. Click the [Apply] button.

3.3.8

Configuring a DNS server

To use a DNS server, configure it. You can configure a DNS server at a later time.

For details on how to back up the specified information, see

3.5 Saving Configuration Information

Note

Operations

1. Click [Network Configuration] - [Network Interface].

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 3 Work before Operating System Installation

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды