Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 267

Страница: 267 / 344

If PSA version 2.8.0 or earlier is installed when the iptables service has stopped, the existing settings are cleared.

Deal with this problem in the following way.

- To use the iptables service:

After making the settings to open the ports necessary for the system, open the necessary ports. For details,

see

TABLE 6.5 Ports to open for the PSA-to-MMB communication LAN interfaces

- To use a firewall tool other than iptables:

The setting of the PSA-to-MMB communication LAN (PSA-MMB_LAN chain) has been added to iptables.

Delete it manually, and then open the necessary ports. For details, see

TABLE 6.5 Ports to open for the PSA-

to-MMB communication LAN interfaces

PSA-to-MMB communication LAN interfaces (for PSA version 2.6 or later)

The firewall settings vary depending on the environment. The settings shown in the following procedure are an

example of settings for PSA-to-MMB communication.

Example: REJECT setting in INPUT and FORWARD

# iptables -L -n

Chain INPUT (policy ACCEPT)

target prot opt source destination

ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED

ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0

ACCEPT all -- 0.0.0.0/0 0.0.0.0/0

ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22

REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-

prohibited

Chain FORWARD (policy ACCEPT)

target prot opt source destination

REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-

prohibited

Chain OUTPUT (policy ACCEPT)

target prot opt source destination

Chain PSA-MMB_LAN (2 references)

target prot opt source destination

ACCEPT all -- 0.0.0.0/0 0.0.0.0/0

ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8

ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 0

ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:161

ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp spt:161

ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:24450

ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:24450

ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:5000

PRIMEQUEST 1000 Series Installation Manual
APPENDIX B Manual PSA Installation and Uninstallation

239

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды