Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 167

Страница: 167 / 344

MMLAN all -- 0.0.0.0/0 0.0.0.0/0

Chain MMLAN (2 references)

target prot opt source destination

ACCEPT udp -- 192.168.0.0/24 192.168.0.1 udp dpts:7000:7100

ACCEPT udp -- 192.168.0.1 192.168.0.0/24 udp spts:7000:7100

ACCEPT udp -- 192.168.0.0/24 192.168.0.1 udp dpt:162

ACCEPT udp -- 192.168.0.1 192.168.0.0/24 udp spt:162

ACCEPT udp -- 192.168.1.5 192.168.0.1 udp dpts:7000:7100

ACCEPT udp -- 192.168.0.1 192.168.1.5 udp spts:7000:7100

ACCEPT udp -- 192.168.1.5 192.168.0.1 udp dpt:162

ACCEPT udp -- 192.168.0.1 192.168.1.5 udp spt:162

7. Save the firewall configuration.

# /sbin/service iptables save

PSA-to-MMB communication LAN interfaces

Open the following ports for use with the PSA-to-MMB communication LAN interfaces.

Usually, the ports are automatically opened during PSA installation.(*)

* In PSA version 2.6 and later, the ports are automatically configured only when PSA is installed from SVIM.

TABLE 6.5 Ports to open for the PSA-to-MMB communication LAN interfaces

Port

Port number

Description

Remarks

snmp port

udp/snmp or 161

For sending and

receiving

web-mmb

communication port

tcp/fj-webgate or 24450 web-mmb communication port

For sending and

receiving

psa-mmb

communication port

tcp/5000 on MMB side Communication using port 5000 on

the MMB side.

The partition acts as the client in this

type of communication, so the

partition uses a dynamic port number

(one of the ports in the range tcp/1025

to 65535).

Under certain circumstances, there is

no need to set port number 5000. One

example is a setting that permits a

connection to be established from the

partition. Another example is a

setting permitting communication

through an established connection

with the partition.

For sending and

receiving

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 6 Work after Operating System Installation (PRIMEQUEST 1800E)

139

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды