Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 228

Страница: 228 / 344

FIGURE 6.33 RAS Support Service screens (no BBU)

- After moving a monitored RAID card to another partition through a partition configuration change, you need

to correct the RAS Support Service settings. First, in the Mounting Dates list, clear the RAID card mounting

date on the original source partition. Then, set the RAID card mounting date on the destination partition.

FIGURE 6.34 RAS Support Service screens (move to another partition)

- The PRIMEQUEST 1000 series server can have multiple partition configurations.

For example, suppose a partition requires many CPUs during the day and a lot of I/O at night, the partition

configuration must change between day and night. This means changes in the SB and IOB connection

configuration.

In this case, to move a RAID card to another partition, determine the primary partition for service life

monitoring and then set the partition in RAS Support Service.

If both partitions are set by mistake, notifications from both partitions will be issued in service life monitoring

for the same RAID card.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 6 Work after Operating System Installation (PRIMEQUEST 1800E)

200

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды