Fujitsu MB90460 Series Скачать руководство пользователя страница 146

Страница: 146 / 739

127

CHAPTER 7 INTERRUPT

■

Hardware Interrupt Structure

Table 7.4-1 lists four mechanisms used for hardware interrupt. These four mechanisms must be included in

the program before hardware interrupt can be used.

These four mechanisms must be included in the program before hardware interrupt can be used.

■

Hardware Interrupt Suppression

Acceptance of hardware interrupt requests is suppressed under the following conditions.

●

Hardware interrupt suppression during writing to the peripheral function control register area

When data is being written to the peripheral function control register area, hardware interrupt requests are

not accepted. This prevents the CPU from making operational mistakes. The mistakes may be caused if an

interrupt request is generated during data is written to the interrupt control registers for a resource. The

peripheral function control register area is not the I/O addressing area at 000000

to 0000FF

, but the area

allocated to the control register of the peripheral function control register and data register.

Figure 7.4-1 shows hardware interrupt operation during writing to the built-in resource area.

Figure 7.4-1 Hardware Interrupt Request while writing to the Peripheral Function Control Register Area

Table 7.4-1 Mechanisms used for Hardware Interrupt

Mechanism

Function

Peripheral function

Interrupt enable bit, interrupt
request bit

Controls interrupt requests from a peripheral
function

Interrupt controller

Interrupt control register (ICR)

Sets the interrupt level and controls EI

CPU

Interrupt enable flag (I)

Identifies the interrupt enable status

Interrupt level mask register
(ILM)

Compares the request interrupt level and
current interrupt level

Microcode

Executes the interrupt processing routine

FFFC00

FFFFFF

in memory

Interrupt vector table

Stores the branch destination address for
interrupt processing

MOV A, #08

MOV io, A

MOV A, 2000H

Interrupt processing

An interrupt request
is generated here

Does not branch
to the interrupt

Branches to
the interrupt

Instruction that writes to the peripheral function control register area

Содержание MB90460 Series




































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MB90460 Series

Отзывы:

Fujitsu MB90460 Series, Руководство по оборудованию, Страница: 146 / 739

Результаты поиска

Содержание MB90460 Series

Отзывы: