background image

External ports

A26361-D1451-Z120-1-6319

English - 7

Interfaces and connectors

The positions of the interfaces and connectors are shown on page "Cover".

The components and connectors marked are not necessarily present on the mainboard.

External ports

The positions of the external ports are shown on page "Cover".

PS/2 keyboard port, purple

PS/2 mouse port, green

Serial interface, turquoise

Parallel port/Printer, burgundy

LAN

LAN connector

USB - Universal Serial Bus, black

Audio output (Line out), light green

Microphone jack (mono), pink

Audio input (Line in), light blue

VGA port, blue (monitor)

LAN connector

This mainboard is equipped with the 82562ET (D1521) or the 82562EM (D1522) LAN controller.
Both LAN controller support transfer speeds of 10 Mbit/s and 100 Mbit/s. The LAN controller are
equipped with a 3 KB transmission and receiving buffer (FIFO) and support WOL function through
Magic Packet

ä

.

It is also possible to boot a device without its own boot hard disk via LAN. Here bootix® LAN BootP
or bootix® PXE are supported.

The LAN RJ45 connector has two LEDs (light emitting diodes).

1

2

1 = 

 

a connection exists (e.g. to a hub).

2 = 

 

Link Mode: the LAN connection is active.

Содержание D1451











































Отзывы: