Fujitsu BS2000 SE Series Скачать руководство пользователя страница 40

Страница: 40 / 93

Opening the rack console

Use the handle to push the cover of the rack console up until the monitor is open at an angle of 110 degrees.

Monitor operating panel

The operating panel is at the bottom right of the monitor.

Power button

Press this button to turn on the power to the monitor, or, if the power is already on, to turn off the power to the

monitor.

Power LED

This LED lights up green when the power to the monitor is on, and lights orange when the monitor is in

energy-saving mode. The light goes off when the monitor is turned off.

MENU/ENTER button

Press this button to open the menu, to select an item to be adjusted, and to save an adjusted setting.

UP button

Press this button to select the right-hand item or to increase the value.

Содержание BS2000 SE Series






























































































Результаты поиска

Содержание BS2000 SE Series

Отзывы:

Похожие инструкции для BS2000 SE Series

Бренды по названию

Популярные бренды

Fujitsu BS2000 SE Series, Основное руководство по эксплуатации

Результаты поиска

Содержание BS2000 SE Series

Отзывы:

Похожие инструкции для BS2000 SE Series

Бренды по названию

Популярные бренды