background image

En-7

Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).

OPERATION

To Select Mode Operation

1

Press the START/STOP button.

The indoor unit’s OPERATION indicator light (red) will be on.
The air conditioner will start operating.

2

Press the MASTER CONTROL button to select the de-
sired mode.

Each time the button is pressed, the mode will change in the following
order.

AUTO

COOL

DRY

*HEAT

FAN

About three seconds later, the entire display will reappear.

To Set the Thermostat

Press the SET TEMP. buttons.

button:

Press to raise the thermostat setting.

button:

Press to lower the thermostat setting.

Thermostat setting range:

AUTO .................................. 64 to 88 

°

F

* Heating ............................... 60 to 88 

°

F

Cooling/Dry ........................ 64 to 88 

°

F

The thermostat cannot be used to set room temperature during the FAN mode (the
temperature will not appear on the remote control unit’s display).

About three seconds later, the entire display will reappear.

The thermostat setting should be considered a standard value, and may differ
somewhat from the actual room temperature.

To Set the Fan Speed

Press the FAN CONTROL button.

Each time the button is pressed, the fan speed changes in the following order:

AUTO

HIGH

MED

LOW

About three seconds later, the entire display will reappear.

When set to AUTO:
* Heating :

Fan operates so as to optimally circulate warm air.
However, the fan will operate at very low speed when the temperature
of the air from the indoor unit is low.

Cooling :

As the room temperature approaches that of the thermostat setting,
the fan speed becomes slower.

Fan

:

The fan alternately turns on and off; when on, the fan runs at the low
fan speed.

The fan will operate at a very low setting during Monitor operation
and at the start of the Heating mode.

d

c

c

c

d

c

c

c

c

SLEEP

TIMER

   SET

TIME

  SET

TEMP 

MASTER

CONTROL

FAN

CONTROL

START

STOP

.

COOL

SLEEP

TIMER

   SET

TIME

  SET

TEMP 

MASTER

CONTROL

FAN

CONTROL

START

STOP

.

To Stop Operation

Press the START/STOP button.

The OPERATION indicator light (red) will turn off.

SLEEP

TIMER

   SET

TIME

  SET

TEMP 

MASTER

CONTROL

FAN

CONTROL

START

STOP

.

AUTO

Example: 

When set to COOL

Example: 

When set to 82 

°

F

Example: 

When set to AUTO

Содержание ABU22



















Отзывы: