FUJIPLA AL-MEISTER ALM3230 Скачать руководство пользователя

Страница: 59 / 68

DryLam

A Trademark of Martin Yale Industries

251 Wedcor Avenue, Wabash, IN 46992

Brian Jennett- Tech-Line & Service Advisor/Manager

Phone: (260-569-7231)

www.DryLam.com

ALM3230 Customer Instruction Manual.docx

Page 59 of 68

5. AUTOMATIC OPERATION (cont’d)

5-4. START OPERATION

1. Make sure Lamination Handle is down

in the Laminate position.

2. Check the settings.

3. Make sure READY lamp is on.

NOTE: Do not press the START button until the machine has been threaded. See

section 4

above on

the proper threading process. Otherwise, damage to the machine can occur.

4. Press the START button. Operation starts.

5. Press STOP button during the operation to stop the lamination.

* NOTE: The STOP button is not an emergency stop. Lamination will stop when the

process is done.

If emergency stop is required simply open the Feeder, or switch off the power switch.

FILM END

AL-ROLL Film has a special feature that allows the end of the film roll to be detected. The last 20" of

each roll of film is colored in black. When this black “leader” passes the Cutter Sensor an error is

displayed and operation stops. Remove and discard the partially laminated sheet and install new film.

Содержание AL-MEISTER ALM3230





































































Результаты поиска

Содержание AL-MEISTER ALM3230

Отзывы:

Похожие инструкции для AL-MEISTER ALM3230

Бренды по названию

Популярные бренды

FUJIPLA AL-MEISTER ALM3230, Инструкция по эксплуатации

Результаты поиска

Содержание AL-MEISTER ALM3230

Отзывы:

Похожие инструкции для AL-MEISTER ALM3230

Бренды по названию

Популярные бренды