FUJIPLA AL-MEISTER ALM3230 страница 24 Скачать руководство пользователя | Manualshive

Страница: 24 / 68

background image

DryLam

A Trademark of Martin Yale Industries

251 Wedcor Avenue, Wabash, IN 46992

Brian Jennett- Tech-Line & Service Advisor/Manager

Phone: (260-569-7231)

ALM3230 Customer Instruction Manual.docx

Page 24 of 68

3. INSTALLATION (cont’d)

4. SET LAMINATION FILM/MANUAL MODE

1. AL-ROLL film is the exclusive lamination film for ALM3230. Always use a combined set of upper and lower

film together (even if using one-sided film) from the same box. Prior to loading film inspect the rolls for

possible shipping damage. Lower film roll must have a valid RFID tag installed and loaded towards the non-

operator side of the machine.

ATTENTION: If this tag is not in place or it has been damaged

the machine will not heat up, or run in automatic mode.

Do not install damaged or “shifted (telescoped)” rolls of film on the ALM3230. These rolls may

have been damaged in shipment. The two sheets of film will not overlap each other properly

and will causes operational problems.

2. Open the cover at the trimmer. Loosen the black knobs and adjust both the left and right levers to the FILM

SET position. Leave this the cover open for the next steps.

Always make sure that the levers are at the film set

position when threading. Otherwise, the threading

card will get caught on the trimmer blades. Damage to

the trimmer blades and jamming of film may occur.

«
...
22
23
24
25
26
...
»

Содержание AL-MEISTER ALM3230





































































Отзывы:

Нет отзывов

Похожие инструкции для AL-MEISTER ALM3230

Бренд: GBC Страницы: 49

Inspire Plus A3

Бренд: GBC Страницы: 12

Бренд: Easymount Страницы: 9

Бренд: Olympia Страницы: 72

Бренд: DataCard Страницы: 85

Бренд: Formica Страницы: 34

Бренд: Advanced Greig Laminators, Inc. Страницы: 42

Бренд: Advanced Greig Laminators Страницы: 45

Бренд: Advanced Greig Laminators Страницы: 50

Бренд: Advanced Greig Laminators, Inc. Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды