Fuji Xerox DocuPrint CM225FW Скачать руководство пользователя | Manualshive

Страница: 52 / 344

background image

52

Printer Connection and Software Installation

Wireless Connection

This section describes how to connect the printer to a computer via wireless network.
Confirm that the Ethernet cable has been disconnected from the printer and the status LED (

Mobile

) is blinking

before configuring the wireless connection.

IMPORTANT:

•

The Wireless LAN feature is not available in all locations. Please check with your local Fuji Xerox representative for
availability of wireless in your location.

•

If you are using a method other than Wi-Fi Protected Setup

™

(WPS) to configure your wireless network settings, be sure to

get the SSID and security information from a system administrator before starting the setup procedure.

•

Be sure to configure necessary settings on the wireless LAN access point (Registrar) or router before starting the printer
setup. For information on the access point or router settings, refer to the manual supplied with the product.

The specifications of wireless setting function are described below:

*1

WPA stands for Wi-Fi Protected Access

®

.

*2

WPS 2.0 compliant. WPS 2.0 works on access points with the following encryption types: Mixed Mode PSK, WPA-PSK-AES,
WPA2-PSK-AES, Open (No Security)

You can select a method to configure a wireless setting from the following:

*1

WPS-PBC (Wi-Fi Protected Setup-Push Button Configuration) is a method to authenticate and register devices required for
wireless configuration, by starting WPS-PBC on the printer with the operator panel menu, and then pressing the button provided on
the wireless LAN access point (Registrar) or router. This setting is available only when the access point supports WPS-PBC.

*2

WPS-PIN (Wi-Fi Protected Setup-Personal Identification Number) is a method to authenticate and register devices required for
wireless configuration, by entering PIN assignments in the printer and computer. This setting, performed through access point, is
available only when the access point of your wireless router supports WPS.

Item

Specification

Connectivity

Wireless

Connectivity Standard

IEEE 802.11b/802.11g/802.11n compliant

Bandwidth

2.4 GHz

Data Transfer Rate

IEEE 802.11b mode: 11, 5.5, 2, 1 Mbps
IEEE 802.11g mode: 54, 48, 36, 24, 18, 12, 9, 6 Mbps
IEEE 802.11n mode: 65 Mbps

Security

64 (40-bit key)/128 (104-bit key) WEP, WPA

™

-PSK (TKIP, AES)

*1

, WPA2

™

-PSK

(AES)

*1

(IEEE 802.1x attestation function of WPA 1x non-corresponds), Mixed

Mode PSK

Certifications

Wi-Fi

®

, Wi-Fi Direct

®

, WPA2.0 (Personal)

Wi-Fi Protected Setup (WPS)

*2

Push Button Configuration (PBC), Personal Identification Number (PIN)

Using the installer on the

Software Pack CD-ROM

(Windows Only) (Recommended for initial setup)

Refer to "Launching the FX Printer Installation Screen" on page 61.

WPS-PBC (Operator Panel Menu)

*1

Refer to "WPS-PBC" on page 53.

WPS-PIN

*2

Refer to "WPS-PIN" on page 53.

Auto SSID Setup

Refer to "Auto SSID Setup" on page 54.

Manual SSID Setup

Refer to "Manual SSID Setup" on page 55.

«
...
50
51
52
53
54
...
»

Содержание DocuPrint CM225FW

























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DocuPrint CM225FW

Color imageCLASS MF8580Cdw

Бренд: Canon Страницы: 750

ImageCLASS 2300

Бренд: Canon Страницы: 8

Color imageCLASS MF8580Cdw

Бренд: Canon Страницы: 750

Color imageCLASS 8180c

Бренд: Canon Страницы: 95

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 49

ImageCLASS 2300

Бренд: Canon Страницы: 156

Бренд: Canon Страницы: 193

Бренд: QMS Страницы: 24

imageCLASS D1120

Бренд: Canon Страницы: 36

ImageCLASS 2300

Бренд: Canon Страницы: 44

Бренд: Canon Страницы: 66

Бренд: Canon Страницы: 11

imageRUNNER ADVANCE 8085

Бренд: Canon Страницы: 176

Бренд: Canon Страницы: 85

imageRUNNER 5070

Бренд: Canon Страницы: 4

imageRUNNER 5570

Бренд: Canon Страницы: 4

IMAGERUNNER 7095 PRINTER

Бренд: Canon Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды