Fuji Xerox DocuPrint CM225FW Скачать руководство пользователя

Страница: 238 / 344

238

Using the Operator Panel Menus and Keypad

Values:

• Software Download

Purpose:
To enable or disable download of firmware updates.
Values:

• Display of Network Information

Purpose:
To show or hide network information in the message field of the top service menu screen.
Values:

• Login Attempts

NOTE:

•

Panel Lock Set

is set to

Enable

Purpose:
To specify the number of error entry attempts allowed when you log in as an administrator in the

Admin Settings

and

Report

List

menu.

Values:

USB Setup

Use the

USB Settings

menu to change printer settings affecting a USB port.

NOTE:

•

The value marked by an asterisk (*) is the factory default setting.

• Port Status

Purpose:
To enable or disable the USB interface.
Values:

Disable

Disables Domain Filtering.

Enable

Only allows e-mails to be sent to specified domains.

Disable

Disables firmware updates.

Enable

Enables firmware updates.

Show IPv4 Address

Shows the IPv4 address of the printer.

Show Host Name

Shows the host name of the printer.

Hide Network Information

Does not show network information.

Off

Does not allow an administrator to log in after one error entry attempt.

Sets the number of error entry attempts allowed when an administrator logs in.

1-10

Disable

Disables the USB interface.

Enable

Enables the USB interface.

Содержание DocuPrint CM225FW
























































































































































































































































































































































Результаты поиска

Содержание DocuPrint CM225FW

Отзывы:

Похожие инструкции для DocuPrint CM225FW

Бренды по названию

Популярные бренды

Fuji Xerox DocuPrint CM225FW, Руководство пользователя

Результаты поиска

Содержание DocuPrint CM225FW

Отзывы:

Похожие инструкции для DocuPrint CM225FW

Бренды по названию

Популярные бренды